EN 15037-4:2010/FprA1

Precast concrete products - Beam-and-block floor systems - Part 4: Expanded polystyrene blocks

EN 15037-4:2010/FprA1

Name:EN 15037-4:2010/FprA1   Standard name:Precast concrete products - Beam-and-block floor systems - Part 4: Expanded polystyrene blocks
Standard number:EN 15037-4:2010/FprA1   language:English language
Release Date:   technical committee:CEN/TC 229 - Precast concrete products
Drafting committee:CEN/TC 229/WG 1 - Products for which the stability requirements is predominant   ICS number:91.100.30 - Concrete and concrete products
SLOVENSKI STANDARD
SIST EN 15037-4:2010/FprA1:2012
01-november-2012
Montažni betonski izdelki - Stropni sistemi iz nosilcev in polnil - 4. del: Polnila iz
ekspandiranega polistirena
Precast concrete products - Beam-and-block floor systems - Part 4: Expanded
polystyrene blocks
Betonfertigteile - Balkendecken mit Zwischenbauteilen - Teil 4: Zwischenbauteile aus
Polystyrolhartschaum
Produits préfabriqués en béton - Systèmes de planchers à poutrelles et entrevous -
Partie 4: Entrevous en polystyrène expansé
Ta slovenski standard je istoveten z: EN 15037-4:2010/FprA1
ICS:
91.060.30 Stropi. Tla. Stopnice Ceilings. Floors. Stairs
91.100.30 Beton in betonski izdelki Concrete and concrete
products
SIST EN 15037-4:2010/FprA1:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 15037-4:2010/FprA1:2012

---------------------- Page: 2 ----------------------

SIST EN 15037-4:2010/FprA1:2012


EUROPEAN STANDARD
FINAL DRAFT
EN 15037-4:2010
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
September 2012
ICS 91.100.30
English Version
Precast concrete products - Beam-and-block floor systems -
Part 4: Expanded polystyrene blocks
Produits préfabriqués en béton - Systèmes de planchers à Betonfertigteile - Balkendecken mit Zwischenbauteilen -
poutrelles et entrevous - Partie 4: Entrevous en polystyrène Teil 4: Zwischenbauteile aus Polystyrolhartschaum
expansé
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 229.

This draft amendment A1, if approved, will modify the European Standard EN 15037-4:2010. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15037-4:2010/FprA1:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 15037-4:2010/FprA1:2012
EN 15037-4:2010/FprA1:2012 (E)
Contents Page
Foreword .3
1 Modification to Clause 2, Normative references .4
2 Modification to 4.3.5.2, Reaction to fire .4
3 Addition of a new sub-clause, 4.3.9,Dangerous substances .4
4 Addition of a new sub-clause, 5.4 Reaction to fire test .4
5 Deletion of the requirement of “Dangerous substances” in Annex ZA .4
6 Modifications to Table ZA.1 Relevant clauses for EPS blocks used in beam-and-block
floor systems .5
7 Modification to ZA.2 Procedure for attestation of conformity of EPS blocks for beam-and-
block floor systems .5

2

---------------------- Page: 4 ----------------------

SIST EN 15037-4:2010/FprA1:2012
EN 15037-4:2010/FprA1:2012 (E)
Foreword
This document (EN 15037-4
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27