EN 1915-2:2001/prA1

Aircraft ground support equipment - General requirements - Part 2: Stability and strength requirements, calculations and test methods

EN 1915-2:2001/prA1

Name:EN 1915-2:2001/prA1   Standard name:Aircraft ground support equipment - General requirements - Part 2: Stability and strength requirements, calculations and test methods
Standard number:EN 1915-2:2001/prA1   language:English language
Release Date:   technical committee:CEN/TC 274 - Aircraft ground support equipment
Drafting committee:CEN/TC 274/SC 1/WG 2 - Strength, stability, testing   ICS number:49.100 - Ground service and maintenance equipment
SLOVENSKI STANDARD
SIST EN 1915-2:2002/kprA1:2008
01-december-2008
3RGSRUQDRSUHPDQDWOHK]DOHWDOVNLSURPHW6SORãQH]DKWHYHGHO=DKWHYH]D
VWDELOQRVWLQY]GUåOMLYRVWL]UDþXQLLQSUHVNXVQLSRVWRSNL
Aircraft ground support equipment - General requirements - Part 2: Stability and strength
requirements, calculations and test methods
Luftfahrt-Bodengeräte - Allgemeine Anforderungen - Teil 2: Standsicherheits- und
Festigkeitsanforderungen, Berechnungen und Prüfverfahren
Matériels au sol pour aéronefs - Exigences générales - Partie 2: Exigences de stabilité et
de résistance mécanique, calculs et méthodes d'essai
Ta slovenski standard je istoveten z: EN 1915-2:2001/prA1
ICS:
49.100 Oprema za servis in Ground service and
vzdrževanje na tleh maintenance equipment
SIST EN 1915-2:2002/kprA1:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1915-2:2002/kprA1:2008

---------------------- Page: 2 ----------------------

SIST EN 1915-2:2002/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 1915-2:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2008
ICS 49.100

English Version
Aircraft ground support equipment - General requirements - Part
2: Stability and strength requirements, calculations and test
methods
Matériels au sol pour aéronefs - Exigences générales - Luftfahrt-Bodengeräte - Allgemeine Anforderungen - Teil 2:
Partie 2: Exigences de stabilité et de résistance Standsicherheits- und Festigkeitsanforderungen,
mécanique, calculs et méthodes d'essai Berechnungen und Prüfverfahren
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 274.
This draft amendment A1, if approved, will modify the European Standard EN 1915-2:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1915-2:2001/prA1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1915-2:2002/kprA1:2008
EN 1915-2:2001/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to the Introduction.4
3 Modification to Clause 1 .4
4 Modification to Clause 2 .4
5 Modification to Clause 3 .5
6 Modification to Clause 4 .5
7 Modification to the heading of Clause 5.5
8 Modification to 5.1 .5
9 Modification to 5.2.4, Table 1.5
10 Modification to 5.3.3.1 .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27