EN ISO 23632:2022

Industrial valves - Design validation-testing of valves (ISO 23632:2021)

EN ISO 23632:2022

Name:EN ISO 23632:2022   Standard name:Industrial valves - Design validation-testing of valves (ISO 23632:2021)
Standard number:EN ISO 23632:2022   language:English language
Release Date:11-Oct-2022   technical committee:CEN/TC 69 - Industrial valves
Drafting committee:CEN/TC 69 - Industrial valves   ICS number:23.060.01 - Valves in general

SLOVENSKI STANDARD
01-december-2022
Industrijski ventili - Validacija zasnove in preskušanje ventilov (ISO 23632:2021)
Industrial valves - Design validation-testing of valves (ISO 23632:2021)
Industriearmaturen - Validierungsprüfung der Konstruktion von Armaturen (ISO
23632:2021)
Robinetterie industrielle - Essais de validation de la conception des appareils de
robinetterie (ISO 23632:2021)
Ta slovenski standard je istoveten z: EN ISO 23632:2022
ICS:
23.060.01 Ventili na splošno Valves in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 23632
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 23.060.01
English Version
Industrial valves - Design validation-testing of valves (ISO
23632:2021)
Robinetterie industrielle - Essais de validation de la Industriearmaturen - Validierungsprüfung der
conception des appareils de robinetterie (ISO Konstruktion von Armaturen (ISO 23632:2021)
23632:2021)
This European Standard was approved by CEN on 2 October 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23632:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 23632:2021 has been prepared by Technical Committee ISO/TC 153 "Valves” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 23632:2022 by
Technical Committee CEN/TC 69 “Industrial valves” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2023, and conflicting national standards shall be
withdrawn at the latest by April 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 23632:2021 has been approved by CEN as EN ISO 23632:2022 without any modification.

INTERNATIONAL ISO
STANDARD 23632
First edition
2021-05
Industrial valves — Design validation-
testing of valves
Robinetterie industrielle - Essais de validation de la conception des
appareils de robinetterie
Reference number
ISO 23632:2021(E)
©
ISO 2021
ISO 23632:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

ISO 23632:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Type test . 3
4.1 Test condition . 3
4.1.1 General. 3
4.1.2 Closure test . 3
4.1.3 Torque measurement . 4
4.1.4 Temperature measurement . 4
4.1.5 Test facility and safety rules . 6
4.1.6 Mechanical-cycle classes . 6
4.2 Test description . 7
4.2.1 General. 7
4.2.2 Test temperatures . 7
4.2.3 Closure test . 8
4.2.4 Unseating torque . 8
4.2.5 Maximum allowable stem torque (MAST) . 8
4.2.6 Post-test examination . 8
4.2.7 Qualification . 8
4.3 Test report . 9
5 Extensions of qualification to the product range. 9
Annex A (informative) Report template .12
Bibliography .14
ISO 23632:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 153, Valves.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

ISO 23632:2021(E)
Introduction
The scope of this document is currently limited to ball and butterfly valves.
The objective of this document is to outline the requirements and methods for evaluating the
performance of metallic industrial valves with respect to seat performance and operating torque
capability. Fugitive emission performance was omitted, as it is covered by ISO 15848-1. The number
of cycles (205) is consistent with the number in C01 of ISO 15848-1:2015. It serves to test the accuracy
and dependability of the measurements and capabilities of a valve as published by the manufacturer in
the valve’s technical documentation.
Type validation is the most reliable method to validate a range of valve products, covering many
aspects, such as its design, material selection and manufacturing processes. It will also serve as a guide
for valve selection, allowing customers to compare different valve types, designs and brands.
Several major customers already require type tests, each having their own requirements and
specifications. Introducing a defined International Standard will reduce manufacturer's costs by
decreasing the number of qualifications, as well as decreasing end-user total cost-of-ownership, by
eliminating the possibility of unintentional design flaws.
This validation will improve performance and safety in the plants by enabling any customer to specify
durable type-tested industrial valves.
INTERNATIONAL
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27