prEN 12977-3

Thermal solar systems and components - Custom built systems - Part 3: Performance characterisation of stores for solar heating systems

prEN 12977-3

Name:prEN 12977-3   Standard name:Thermal solar systems and components - Custom built systems - Part 3: Performance characterisation of stores for solar heating systems
Standard number:prEN 12977-3   language:English language
Release Date:   technical committee:CEN/TC 312 - Thermal solar systems and components
Drafting committee:CEN/TC 312 - Thermal solar systems and components   ICS number:
SLOVENSKI STANDARD
oSIST prEN 12977-3:2006
01-november-2006
7RSORWQLVRQþQLVLVWHPLLQVHVWDYQLGHOL1HVHULMVNRL]GHODQLVLVWHPLGHO
'RORþDQMHSUHVNXVQLKPHWRG]DKUDQLOQLNHWRSORWHRJUHYDQHVVRQFHP
Thermal solar systems and components - Custom built systems - Part 3: Performance
characterisation of stores for solar heating systems
Ta slovenski standard je istoveten z: prEN 12977-3
ICS:
27.160 6RQþQDHQHUJLMD Solar energy engineering
91.140.10 Sistemi centralnega Central heating systems
ogrevanja
91.140.65 Oprema za ogrevanje vode Water heating equipment
oSIST prEN 12977-3:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 12977-3:2006

---------------------- Page: 2 ----------------------
oSIST prEN 12977-3:2006
EUROPEAN STANDARD
DRAFT
prEN 12977-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2006
ICS 91.140.10; 91.140.65; 27.160 Will supersede ENV 12977-3:2001
English Version
Thermal solar systems and components - Custom built systems
- Part 3: Performance test methods for solar water heater stores
Installations solaires thermiques et leurs composants - Thermische Solaranlagen und ihre Bauteile -
Installations assemblées à façon - Partie 3: Méthodes Kundenspezifisch gefertigte Anlagen - Teil 3:
d'essai des performances des dispositifs de stockage des Leistungsprüfung von Warmwasserspeichern für
installations de chauffage solaire de l'eau Solaranlagen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 312.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12977-3:2006: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 12977-3:2006
prEN 12977-3:2006 (E)
Contents Page
Foreword.4
Introduction .4
1 Scope.4
2 Normative references.4
3 Terms and definitions .5
4 Symbols and abbreviations .9
5 Store classification.10
6 Laboratory store testing.10
6.1 Requirements on the testing stand.10
6.1.1 General.10
6.1.2 Measured quantities and measuring procedure.1
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27