EN 1434-1:2015/prA1

Thermal energy meters - Part 1: General requirements

EN 1434-1:2015/prA1

Name:EN 1434-1:2015/prA1   Standard name:Thermal energy meters - Part 1: General requirements
Standard number:EN 1434-1:2015/prA1   language:English language
Release Date:   technical committee:CEN/TC 176 - Heat meters
Drafting committee:CEN/TC 176/WG 2 - Heat Meters - Requirements, test methods and technical editing   ICS number:17.200.10 - Heat. Calorimetry

SLOVENSKI STANDARD
01-december-2017
Toplotni števci - 1. del: Splošne zahteve
Heat meters - Part 1: General requirements
Wärmezähler - Teil 1: Allgemeine Anforderungen
Compteurs d'énergie thermique - Partie 1 : Prescriptions générales
Ta slovenski standard je istoveten z: EN 1434-1:2015/prA1
ICS:
17.200.10 Toplota. Kalorimetrija Heat. Calorimetry
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
EN 1434-1:2015
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
October 2017
ICS 17.200.10
English Version
Thermal energy meters - Part 1: General requirements
Compteurs d'énergie thermique - Partie 1 : Wärmezähler - Teil 1: Allgemeine Anforderungen
Prescriptions générales
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 176.

This draft amendment A1, if approved, will modify the European Standard EN 1434-1:2015. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1434-1:2015/prA1:2017 E
worldwide for CEN national Members.

EN 1434-1:2017/prA1:2017 (E)
Contents Page
European foreword . 3
1 Modification to the English title . 4
2 Modifications overall the document . 4
3 Modification to Clause 3, "Terms and definitions". 4
4 Modification to subclause 6.10, "Software" . 4
5 Modification to the "Bibliography" . 4
6 Modification to Annex ZA . 4
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/32/EU aimed to be covered . 5

EN 1434-1:2017/prA1:2017 (E)
European foreword
This document (EN 1434-1:2017/prA1:2017) has been prepared by Technical Committee CEN/TC 176
“Thermal energy meters”, the secretariat of which is held by SIS.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this
document.
EN 1434-1:2017/prA1:2017 (E)
1 Modification to the English title
Replace the the English title with the following:
“Thermal energy meters — Part 1: General requirements".
The German title "Wärmezähler — Teil 1: Allgemeine Anforderungen" and the French title "Compteurs
d’énergie thermique — Partie 1: Precriptions générales" remain unchanged.
2 Modifications overall the document
Overall the document, replace "heat meter" with "thermal energy meter”.
Overall the document, replace "heating/cooling meter" with "thermal energy meter".
Overall the document, replace the references "EN 1434-X:2015" with "EN 1434-X:2015+prA1:2017".
3 Modification to Clause 3, "Terms and definitions"
Replace "heat meter or cooling meter" with "thermal energy meter" to read:
"3.28
meter for smart metering
thermal energy meter with the capability of data communication and support of smart metering
functionalities
Note 1 to entry: Data could be transmitted via user interface and/ or communi
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27