EN 88-2:2022

Safety and control devices for gas burners and gas burning appliances - Part 2: Pressure regulators for inlet pressures above 50 kPa up to and including 500 kPa

EN 88-2:2022

Name:EN 88-2:2022   Standard name:Safety and control devices for gas burners and gas burning appliances - Part 2: Pressure regulators for inlet pressures above 50 kPa up to and including 500 kPa
Standard number:EN 88-2:2022   language:English language
Release Date:11-Oct-2022   technical committee:CEN/TC 58 - Safety and control devices for burners and appliances burning gaseous or liquid fuels
Drafting committee:CEN/TC 58/WG 13 - Mechanics   ICS number:23.060.40 - Pressure regulators

SLOVENSKI STANDARD
01-december-2022
Nadomešča:
SIST EN 88-2:2008
Varnostne in nadzorne naprave za plinske gorilnike in plinske aparate - 2. del:
Regulatorji tlaka za vstopne tlake nad 50 kPa do vključno 500 kPa
Safety and control devices for gas burners and gas burning appliances - Part 2: Pressure
regulators for inlet pressures above 50 kPa up to and including 500 kPa
Sicherheits- und Regeleinrichtungen für Gasbrenner und Gasgeräte - Teil 2: Druckregler
für Eingangsdrücke über 50 kPa bis einschließlich 500 kPa
Dispositifs de sécurité et de contrôle pour les brûleurs à gaz et appareils utilisant des
combustibles gazeux - Partie 2 : Régulateurs de pression pour pressions amont
comprises entre 50 kPa et 500 kPa
Ta slovenski standard je istoveten z: EN 88-2:2022
ICS:
23.060.40 Tlačni regulatorji Pressure regulators
27.060.20 Plinski gorilniki Gas fuel burners
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 88-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 23.060.40 Supersedes EN 88-2:2007
English Version
Safety and control devices for gas burners and gas burning
appliances - Part 2: Pressure regulators for inlet pressures
above 50 kPa up to and including 500 kPa
Dispositifs de sécurité et de contrôle pour les brûleurs Sicherheits- und Regeleinrichtungen für Gasbrenner
à gaz et appareils utilisant des combustibles gazeux - und Gasgeräte - Teil 2: Druckregler für Eingangsdrücke
Partie 2 : Régulateurs de pression pour pressions über 50 kPa bis einschließlich 500 kPa
amont comprises entre 50 kPa et 500 kPa
This European Standard was approved by CEN on 8 August 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 88-2:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 6
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 9
4 Classification . 14
4.1 Classes of control . 14
4.2 Groups of control . 14
4.3 Classes of control functions . 14
4.4 Types of DC supplied controls . 14
5 Test conditions and uncertainty of measurements . 14
6 Design and construction . 15
6.1 General . 15
6.2 Mechanical parts of the control . 15
6.3 Materials . 17
6.4 Gas connections . 18
6.5 Electrical parts of the control . 18
6.6 Protection against internal faults for the purpose of functional safety . 18
7 Performance . 18
7.1 General . 18
7.2 Leak-tightness . 19
7.3 Torsion and bending . 19
7.4 Rated flow rate . 19
7.5 Durability . 20
7.6 Performance tests for electronic controls . 20
7.7 Long-term performance for electronic controls . 20
7.8 Data exchange . 20
7.101 Pressure regulator performance . 20
7.102 Safety devices . 26
8 Electrical requirements . 31
8.1 General . 31
8.2 Protection by enclosure . 31
8.101 Plug connections. 31
9 Electromagnetic compatibility (EMC) . 32
9.1 Protection against environmental influences . 32
9.2 Supply voltage variations below 85 % of rated voltage . 32
9.3 Voltage dips and interruptions . 32
9.4 Supply frequency variations . 32
9.5 Surge immunity tests . 32
9.6 Electrical fast transient/burst . 32
9.7 Immunity to conducted disturbances induced by radio frequency fields . 32
9.8 Immunity to radiated disturbances induced by radio frequency fields . 32
9.9 Electrostatic discharge tests . 32
9.10 Power frequency magnetic field immunity tests . 32
9.11 Harmonics and interharmonics including mains signalling at a. c. power port, low
frequency immunity tests . 32
10 Marking, instructions . 33
10.1 Marking . 33
10.2 Instructions . 33
10.3 Warning notice . 34
Annex A (informative) Abbreviations and Symbols . 35
Annex B (informative) Leak-tightness tests for gas controls – volumetric method . 36
Annex C (informative) Leak-tightness tests for gas controls – pressure loss method . 37
Annex D (normative) Conversion of pressure loss into leakage rate . 38
Annex E (normative) Electrical/electronic component fault modes . 39
Annex F (normative) Additional requirements for safety accessories and pressure
accessories as defined in EU Directive 2014/68/EU. 40
Annex G (normative) Materials for pressurized parts . 41
Annex H (normative) Additional materials for pressurized parts . 42
Annex I (normative) Requirements for controls used in DC supplied burners and
appliances burning gaseous or liquid fuels. 43
Annex J (normative) Method for the determination of a Safety Integrity Level (SIL) . 44
Annex K (normative) Method for the determination of a Performance Level (PL) . 45
Annex L (informative) Relationship between Safety Integrity Level (SIL) and Performance
Level (PL) . 46
Annex M (normative) Reset functions . 47
Annex N (informative) Guidance document on Environmental Aspects . 48
Annex O (normative) Seals of elastomer, cork and synthetic fibre mixtures . 49
Annex AA (informative) Typical pressure regulators and safety devices . 50
AA.1 Main components of a pressure regulator . 50
AA.2 Main components of a safety shut-off device . 53
Annex BB (informative) Overview of requirements and test conditions (as given in 7.101),
and examples of performance curves for pressure regulators . 55
Annex CC (normative) Creep relief device . 58
CC.1 General . 58
CC.2 Design and construction . 58
CC.3 Performance requirements . 58
CC.4 Marking, instructions . 58
Annex DD (informative) Comparison between EN 334:2019 and EN 88-2:2022 . 59
Annex ZA (informative) Relationship between this Eu
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27