|
SIST EN 709:1998/oprA2:2007
01-december-2007
.PHWLMVNLLQJR]GDUVNLVWURML(QRRVQLWUDNWRUMLVSULNOMXþHQLPSUHNRSDOQLNRP
PRWRUQLSUHNRSDOQLNLLQPRWRUQLSUHNRSDOQLNLVSRJRQVNLP D NROHVRP D 9DUQRVW
Agricultural and forestry machinery - Pedestrian controlled tractors with mounted rotary
cultivators, motor hoes, motor hoes with drive wheel(s) - Safety
Ta slovenski standard je istoveten z: EN 709:1997/prA2
ICS:
65.060.10 Kmetijski traktorji in prikolice Agricultural tractors and
trailed vehicles
65.060.20 Oprema za obdelovanje tal Soil-working equipment
SIST EN 709:1998/oprA2:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
EN 709:1997
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
September 2007
ICS 65.060.10; 65.060.20
English Version
Agricultural and forestry machinery - Pedestrian controlled
tractors with mounted rotary cultivators, motor hoes, motor hoes
with drive wheel(s) - Safety
Matériels agricoles et forestiers - Motoculteurs avec fraises
portées, motobineuses et fraises à roue(s) motrice(s) -
Sécurité
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 144.
This draft amendment A2, if approved, will modify the European Standard EN 709:1997. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 709:1997/prA2:2007: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 709:1997/prA2:2007 (E)
Contents Page
Foreword.3
1 Modification to Clause 3 .4
2 Modification to Clause 5.3 .4
4 Modification to Clause 5.5 .4
5 Modification to Clause 5.11 .6
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EC Directive 2006/42/EC, Machinery Directive.10
2
---------------------- Page: 3 ----------------------
EN 709:1997/prA2:2007 (E)
Foreword
This document (EN 709:1997/prA2:2007) has been prepared by Technical Committee CEN/TC 144 “Tractors
and machinery for agriculture and foresrty”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annex ZA, which is an integral part of this document.
3
---------------------- Page: 4 ----------------------
EN 709:1997/prA2:2007 (E)
1 Modification to Clause 3
Add the following new definition:
"3.7
maximum operating engine speed
highest engine speed obtainable when adjusted in accordance with the machine manufacturer’s specifications
and/or instructions with the tool
...