EN 1870-14:2007/prA1

Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines

EN 1870-14:2007/prA1

Name:EN 1870-14:2007/prA1   Standard name:Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines
Standard number:EN 1870-14:2007/prA1   language:English language
Release Date:   technical committee:CEN/TC 142 - Woodworking machines - Safety
Drafting committee:CEN/TC 142/WG 4 - Circular sawing machines   ICS number:79.120.10 - Woodworking machines
SLOVENSKI STANDARD
SIST EN 1870-14:2008/kprA1:2009
01-maj-2009
Varnost lesnoobdelovalnih strojev - Krožne žage - 14. del: Vertikalni krožni žagalni
stroji
Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel
sawing machines
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 14:
Vertikalplattenkreissägemaschinen
Sécurité des machines pour le travail du bois - Machines à scier circulaires - Partie 14:
Scies à panneaux verticales
Ta slovenski standard je istoveten z: EN 1870-14:2007/prA1
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870-14:2008/kprA1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1870-14:2008/kprA1:2009

---------------------- Page: 2 ----------------------

SIST EN 1870-14:2008/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1870-14:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2009
ICS 79.120.10

English Version
Safety of woodworking machines - Circular sawing machines -
Part 14: Vertical panel sawing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scier circulaires - Partie 14: Scies à panneaux verticales Kreissägemaschinen - Teil 14:
Vertikalplattenkreissägemaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1870-14:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-14:2007/prA1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1870-14:2008/kprA1:2009
EN 1870-14:2007/prA1:2009 (E)
Contents Page
Foreword .3
1 Modification to the Foreword .4
2 Modification to Clause 2, Normative references .4
3 Modification to Clause 4, List of significant hazards .4
4 Modification to 5.4.5, Ergonomics and handling .4
5 Modification to 6.2.1, Marking of the machine .4
6 Modification to 6.3, Instruction handbook .4
7 Modification to Annex ZA .5
8 Addition of Annex ZB .5


2

---------------------- Page: 4 ----------------------

SIST EN 1870-14:2008/kprA1:2009
EN 1870-14:2007/prA1:2009 (E)
Foreword
This document (EN 1870-14:2007/prA1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requireme
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27