EN 12001:2003/prA1

Conveying, spraying and placing machines for concrete and mortar - Safety requirements

EN 12001:2003/prA1

Name:EN 12001:2003/prA1   Standard name:Conveying, spraying and placing machines for concrete and mortar - Safety requirements
Standard number:EN 12001:2003/prA1   language:English language
Release Date:   technical committee:CEN/TC 151 - Construction equipment and building material machines - Safety
Drafting committee:CEN/TC 151/WG 8 - Concrete preparation and handling equipment - Safety   ICS number:91.220 - Construction equipment
SLOVENSKI STANDARD
SIST EN 12001:2004/kprA1:2009
01-junij-2009
Stroji za transport, brizganje in polaganje betona in malte - Varnostne zahteve
Conveying, spraying and placing machines for concrete and mortar - Safety
requirements
Förder-, Spritz- und Verteilmaschinen für Beton und Mörtel - Sicherheitsanforderungen
Machines pour le transport, la projection et la distribution de béton et mortier -
Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 12001:2003/prA1
ICS:
91.220 Gradbena oprema Construction equipment
SIST EN 12001:2004/kprA1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 12001:2004/kprA1:2009

---------------------- Page: 2 ----------------------

SIST EN 12001:2004/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 12001:2003
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
April 2009
ICS 91.220

English Version
Conveying, spraying and placing machines for concrete and
mortar - Safety requirements
Machines pour le transport, la projection et la distribution Förder-, Spritz- und Verteilmaschinen für Beton und Mörtel
de béton et mortier - Prescriptions de sécurité - Sicherheitsanforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 12001:2003. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12001:2003/prA1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 12001:2004/kprA1:2009
EN 12001:2003/prA1:2009 (E)
Contents Page
Foreword .3
1 Modification to the Introduction .4
2 Modification to the Scope .4
3 Modification to Clause 2, Normative references .4
4 Modification to Clause 3, Terms and definitions .5
5 Modification to Clause 4, List of significant hazards .6
6 Modification to Clause 5, Safety requirements and/or protective measures .6
7 Modification to 5.1, Requirements common to all machines .7
8 Modification to 5.2, Specific requirements for single machines .7
9 Modification to 5.3, Machinery groups .7
10 Modification to 5.4, Control requirements (electrical and hydraulic) .9
11 Modification to 5.4.1, Hopper cover .9
12 Modification to 5.4.3, Stabilisers .9
13 Modification to 5.4.4, Emergency-stop devices . 10
14 Modification to 5.4.5, Concrete-placing boom including slewing mechanism.
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27