EN 13611:2007/FprA1

Safety and control devices for gas burners and gas burning appliances - General requirements

EN 13611:2007/FprA1

Name:EN 13611:2007/FprA1   Standard name:Safety and control devices for gas burners and gas burning appliances - General requirements
Standard number:EN 13611:2007/FprA1   language:English language
Release Date:   technical committee:CEN/TC 58 - Safety and control devices for burners and appliances burning gaseous or liquid fuels
Drafting committee:CEN/TC 58/WG 11 - Generics   ICS number:23.060.40 - Pressure regulators
SLOVENSKI STANDARD
SIST EN 13611:2008/oprA1:2010
01-februar-2010
Varnostne in nadzorne naprave za plinske gorilnike in plinske aparate - Splošne
zahteve - Dopolnilo A1
Safety and control devices for gas burners and gas burning appliances - General
requirements
Sicherheits-, Regel- und Steuereinrichtungen für Gasbrenner und Gasgeräte -
Allgemeine Anforderungen
Équipements auxiliaires pour brûleurs à gaz et appareils à gaz - Exigences générales
Ta slovenski standard je istoveten z: EN 13611:2007/prA1
ICS:
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
27.060.20 Plinski gorilniki Gas fuel burners
SIST EN 13611:2008/oprA1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13611:2008/oprA1:2010

---------------------- Page: 2 ----------------------

SIST EN 13611:2008/oprA1:2010
EUROPEAN STANDARD
DRAFT
EN 13611:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
October 2009
ICS 23.060.40

English Version
Safety and control devices for gas burners and gas burning
appliances - General requirements
Equipements auxiliaires pour brûleurs à gaz et appareils à Sicherheits-, Regel- und Steuereinrichtungen für
gaz - Exigences générales Gasbrenner und Gasgeräte - Allgemeine Anforderungen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 58.
This draft amendment A1, if approved, will modify the European Standard EN 13611:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13611:2007/prA1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13611:2008/oprA1:2010
EN 13611:2007/prA1:2009 (E)
Contents Page
Foreword .4
Annex J (normative) Method for the determination of a Safety integrity level (SIL) .6
J.1 Scope .6
J.2 Normative References .6
J.3 Terms and definitions .7
J.4 Symbols .8
J.5 Special requirements to determine a Safety Integrity Level (SIL) .8
J.5.1 Functional safety .8
J.5.2 Management of functional safety .9
J.5.2.1 Methods of fault prevention .9
J.5.2.2 Functional Safety Management System .9
J.5.2.3 Specification of safety requirements .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27