EN 16230-1:2013/FprA1

Leisure karts - Part 1: Safety requirements and test methods for karts

EN 16230-1:2013/FprA1

Name:EN 16230-1:2013/FprA1   Standard name:Leisure karts - Part 1: Safety requirements and test methods for karts
Standard number:EN 16230-1:2013/FprA1   language:English language
Release Date:   technical committee:CEN/TC 354 - Ride-on, motorized vehicles intended for the transportation of persons and goods and not intended for use on public roads - Safety requirements
Drafting committee:CEN/TC 354/WG 3 - Go-karts   ICS number:43.100 - Passenger cars. Caravans and light trailers
SLOVENSKI STANDARD
SIST EN 16230-1:2014/kFprA1:2014
01-oktober-2014
*RNDUWL]DSURVWLþDVGHO9DUQRVWQH]DKWHYHLQSUHVNXVQHPHWRGH]DJRNDUWH
Leisure karts - Part 1: Safety requirements and test methods for karts
Freizeitkarts - Teil 1: Sicherheitstechnische Anforderungen und Prüfverfahren für Karts
Karts de loisir - Partie 1: Exigences de sécurité et méthodes d'essais relatives aux karts
Ta slovenski standard je istoveten z: EN 16230-1:2013/FprA1
ICS:
43.160 Vozila za posebne namene Special purpose vehicles
97.220.01 âSRUWQDRSUHPDLQ Sports equipment and
SULSRPRþNLQDVSORãQR facilities in general
SIST EN 16230-1:2014/kFprA1:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 16230-1:2014/kFprA1:2014

---------------------- Page: 2 ----------------------

SIST EN 16230-1:2014/kFprA1:2014

EUROPEAN STANDARD
FINAL DRAFT
EN 16230-1:2013
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA1
July 2014
ICS 43.100
English Version
Leisure karts - Part 1: Safety requirements and test methods for
karts
Karts de loisir - Partie 1: Exigences de sécurité et méthodes Freizeitkarts - Teil 1: Sicherheitstechnische Anforderungen
d'essais relatives aux karts und Prüfverfahren für Karts
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 354.

This draft amendment A1, if approved, will modify the European Standard EN 16230-1:2013. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16230-1:2013/FprA1:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 16230-1:2014/kFprA1:2014
EN 16230-1:2013/FprA1:2014 (E)
Contents
Page
Foreword .3
1 Modification to Table 1 - Type of kart - Manufacturers design parameters .4
2 Modification to 7.4.1.2 "Additional requirements for all-around protection having a
shaped surface" .5
3 Modification to 7.5.1.2 "Mechanical components of the brake system" .5
4 Modification to 9.2 "User manual" .6
5 Modification to 9.4 "Signs (pictogram), written warnings" .7
6 Modification to A.3.2 "Test method for the distance between the ground and lower edge
of the protection (a value – Figure 2)" .7
7 Modification to A.3.3 “Test method to measure the distance between the ground and the
upper edge of the protection (b value – Figure 2)” .8
8 Modification to E.2 "Coupling the hand and body to the vibration source".8
9 Modification to E.7 "Information to be reported" .8


2

----
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27