|
SIST EN 1248:2002/kprA1:2008
01-december-2008
Livarski stroji - Varnostne zahteve za opremo za peskanje
Foundry machinery - Safety requirements for abrasive blasting equipment
Gießereimaschinen - Sicherheitsanforderungen für Strahlanlagen
Machines de fonderie - Prescriptions de sécurité pour équipements de grenaillage
Ta slovenski standard je istoveten z: EN 1248:2001/prA1
ICS:
25.120.30 Livarska oprema Moulding equipment
SIST EN 1248:2002/kprA1:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1248:2002/kprA1:2008
---------------------- Page: 2 ----------------------
SIST EN 1248:2002/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 1248:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2008
ICS 25.120.30
English Version
Foundry machinery - Safety requirements for abrasive blasting
equipment
Machines de fonderie - Prescriptions de sécurité pour Gießereimaschinen - Sicherheitsanforderungen für
équipements de grenaillage Strahlanlagen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 202.
This draft amendment A1, if approved, will modify the European Standard EN 1248:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1248:2001/prA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1248:2002/kprA1:2008
EN 1248:2001/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to "Contents" .4
2 Modification to "Foreword" .4
3 Modification to "Introduction".4
4 Modification to Clause "2 Normative references".4
5 Modification to Clause "3 Terms and definitions" .6
6 Modification to Clause "4 Hazards".6
7 Modification to "5.1 General" .7
8 Modification to Table 1 of Clause "5 Safety requirements and/or measures" .8
9 Modification to Clause "6 Verification of the safety requirements and/or measures".21
10 Modification to Clause "7 Information for use" .21
11 Modification to Annex B "Figure B.1 — Processing scheme with abrasive blasting media
preparation (see 3.2)".24
12 Modification to Annex ZA .26
13 Addition of Annex ZB .26
14 Modification to "Bibliography".
...