prEN 15571

Machines and plants for minig and tooling of natural stones - Safety - Requirements for surface finishing machines

prEN 15571

Name:prEN 15571   Standard name:Machines and plants for minig and tooling of natural stones - Safety - Requirements for surface finishing machines
Standard number:prEN 15571   language:English language
Release Date:   technical committee:CEN/TC 151 - Construction equipment and building material machines - Safety
Drafting committee:CEN/TC 151/WG 11 - Machines and plants for mining and tooling of natural stone - Safety   ICS number:25.080.50 - Grinding and polishing machines
SLOVENSKI STANDARD
oSIST prEN 15571:2007
01-januar-2007
Stroji in obrati za miniranje in obdelavo naravnega kamna - Varnost - Zahteve za
stroje za dodelavo površine
Machines and plants for minig and tooling of natural stones - Safety - Requirements for
surface finishing machines
Maschinen und Anlagen zur Gewinnung und Bearbeitung von Naturstein - Sicherheit -
Anforderungen für Flächenschleifmaschinen
Machines et équipements pour l'exploitation et l'usinage de pierres naturelles - Sécurité -
Prescripitions relatives aux machines de finition de surface
Ta slovenski standard je istoveten z: prEN 15571
ICS:
25.080.50 Brusilni in polirni stroji Grinding and polishing
machines
73.120 Oprema za predelavo rudnin Equipment for processing of
minerals
oSIST prEN 15571:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 15571:2007

---------------------- Page: 2 ----------------------
oSIST prEN 15571:2007
EUROPEAN STANDARD
DRAFT
prEN 15571
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2006
ICS

English Version
Machines and plants for minig and tooling of natural stones -
Safety - Requirements for surface finishing machines
Maschinen und Anlagen zur Gewinnung und Bearbeitung
von Naturstein - Sicherheit - Anforderungen für
Flächenschleifmaschinen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 151.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15571:2006: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 15571:2007
prEN 15571:2006 (E)
Contents Page
Foreword.3
Introduction .4
1 Scope.4
2 Normative references.4
3 Terms and definitions – Symbols and abbreviated terms.6
4 List of significant hazards .10
5 Safety requirements and/or protective measures.10
5.1 Mechanical hazards.10
5.1.1 General.10
5.2 Electrical hazards.13
5.3 Electromagnetic Radiation.14
5.4 Hydraulic and pneumatic components.14
6 Verification of sa
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27