|
SLOVENSKI STANDARD
01-junij-2022
Nadomešča:
SIST EN 1159-1:2004
SIST EN 1159-1:2004/AC:2007
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Termofizikalne
lastnosti keramičnih kompozitov - Določanje toplotne razteznosti (ISO 17139:2014)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Thermophysical
properties of ceramic composites - Determination of thermal expansion (ISO
17139:2014)
Hochleistungskeramik - Thermophysikalische Eigenschaften keramischer
Verbundwerkstoffe - Bestimmung der Wärmeausdehnung (ISO 17139:2014)
Céramiques techniques - Propriétés thermophysiques des composites céramiques -
Détermination de la dilatation thermique (ISO 17139:2014)
Ta slovenski standard je istoveten z: EN ISO 17139:2022
ICS:
81.060.30 Sodobna keramika Advanced ceramics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 17139
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2022
EUROPÄISCHE NORM
ICS 81.060.30 Supersedes EN 1159-1:2003
English Version
Fine ceramics (advanced ceramics, advanced technical
ceramics) - Thermophysical properties of ceramic
composites - Determination of thermal expansion (ISO
17139:2014)
Céramiques techniques - Propriétés thermophysiques Hochleistungskeramik - Thermophysikalische
des composites céramiques - Détermination de la Eigenschaften keramischer Verbundwerkstoffe -
dilatation thermique (ISO 17139:2014) Bestimmung der Wärmeausdehnung (ISO 17139:2014)
This European Standard was approved by CEN on 27 March 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17139:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 17139:2014 has been prepared by Technical Committee ISO/TC 206 "Fine ceramics” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 17139:2022
by Technical Committee CEN/TC 184 “Advanced technical ceramics” the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2022, and conflicting national standards shall
be withdrawn at the latest by October 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1159-1:2003.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 17139:2014 has been approved by CEN as EN ISO 17139:2022 without any modification.
INTERNATIONAL ISO
STANDARD 17139
First edition
2014-06-15
Fine ceramics (advanced ceramics,
advanced technical ceramics) —
Thermophysical properties of ceramic
composites — Determination of
thermal expansion
Céramiques techniques — Propriétés thermophysiques des composites
céramiques — Détermination de la dilatation thermique
Reference number
ISO 17139:2014(E)
©
ISO 2014
ISO 17139:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
ISO 17139:2014(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
4.1 General . 2
4.2 Direct measurement . 2
4.3 Differential method . 2
5 Apparatus . 2
5.1 Construction materials . 2
5.2 Heating and cooling device. 2
5.3 Temperature measurement . 2
5.4 Test piece mounting . 2
5.5 System for measuring and recording the thermal expansion . 3
5.6 Test piece measurement . 3
6 Specimens . 3
6.1 Test pieces . 3
6.2 Reference pieces . 3
6.3 Dimensions . 3
7 Procedure. 4
8 Calculations. 5
8.1 Direct measurement . 5
8.2 Differential method . 5
9 Test report . 6
Annex A (normative) Direct measurement apparatus . 9
Annex B (normative) Differential type measurement apparatus .11
Bibliography .12
ISO 17139:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 206, Fine ceramics.
iv © ISO 2014 – All rights reserved
INTERNATIONAL STANDARD ISO 17139:2014(E)
Fine ceramics (advanced ceramics, advanced technical
ceramics) — Thermophysical properties of ceramic
composites — Determination of thermal expansion
1 Scope
This International Standard describes methods for the determination of linear thermal expansion
characteristics of ceramic matrix composite materials up to 2 300 K, and is applicable to 1D, 2D, and nD
materials.
The method describes general principles of construction, calibration, and operation of the equipment.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
ind
...