EN 1501-1:1998/FprA2

Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 1: Rear-end loaded refuse collection vehicles

EN 1501-1:1998/FprA2

Name:EN 1501-1:1998/FprA2   Standard name:Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 1: Rear-end loaded refuse collection vehicles
Standard number:EN 1501-1:1998/FprA2   language:English language
Release Date:   technical committee:CEN/TC 183 - Waste management
Drafting committee:CEN/TC 183/WG 2 - Waste collection vehicles and their associated lifting devices   ICS number:43.160 - Special purpose vehicles
SLOVENSKI STANDARD
SIST EN 1501-1:2000/kFprA2:2009
01-junij-2009
9R]LOD]D]ELUDQMHRGSDGNRYLQSULSDGDMRþLL]WUHVDOQLNL6SORãQHLQYDUQRVWQH
]DKWHYHGHO9R]LOD]D]ELUDQMHRGSDGNRY]QDNODGDQMHP]DGDM
Refuse collection vehicles and their associated lifting devices - General requirements
and safety requirements - Part 1: Rear-end loaded refuse collection vehicles
Ta slovenski standard je istoveten z: EN 1501-1:1998/FprA2
ICS:
43.160 Vozila za posebne namene Special purpose vehicles
SIST EN 1501-1:2000/kFprA2:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1501-1:2000/kFprA2:2009

---------------------- Page: 2 ----------------------

SIST EN 1501-1:2000/kFprA2:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1501-1:1998
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA2
April 2009
ICS 43.160

English Version
Refuse collection vehicles and their associated lifting devices -
General requirements and safety requirements - Part 1: Rear-
end loaded refuse collection vehicles
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 183.
This draft amendment A2, if approved, will modify the European Standard EN 1501-1:1998. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1501-1:1998/FprA2:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1501-1:2000/kFprA2:2009
EN 1501-1:1998/FprA2:2009 (E)
Contents Page
Foreword .3
1 Modification to Clause 2 .4
2 Modifications to Clause 6 .4
3 Modification to Clause 7 .5
4 Modification to Annex ZA .6
5 Addition of Annex ZB .6

2

---------------------- Page: 4 ----------------------

SIST EN 1501-1:2000/kFprA2:2009
EN 1501-1:1998/FprA2:2009 (E)
Foreword
This document (EN 1501-1:1998/FprA2:2009) has been prepared by Technical Committee CEN/TC 183
“Waste management”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
3

---------------------- Page: 5 ----------------------

SIST EN 1501-1:2000/kFprA2:2009
EN 1501-1:1998/FprA2:2009 (E)
1 Modification to Clause 2
Delete the following references:
"prEN 31689, Acoustics – Systematic collection and comparison of noise emission data for machinery and
equipment (ISO/DIS 11689:1993)
prEN 32001, Acoustics – Noise emitted by machinery and equipment – Rules for the drafting and presentation
of a noise test code
ISO/DIS 4871, Acoustics – Declaration and verification of noise emitted by machinery and equipment
I
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27