|
SIST EN 1870-4:2002/kprA1:2009
01-april-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY.URåQHåDJHGHO 9HþOLVWQHNURåQHåDJH]D
Y]GROåQLSUHUH]]URþQLPSRGDMDQMHPLQDOLRGY]HPRP
Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip
sawing machines with manual loading and/or unloading
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 4:
Mehrblattkreissägemaschinen für Längsschnitt mit Handbeschickung und/oder
Handentnahme
Sécurité des machines pour le travail du bois - Machines à scies circulaires - Partie 4:
Scies circulaires à déligner multilames à chargement et/ou déchargement manuel
Ta slovenski standard je istoveten z: EN 1870-4:2001/prA1
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870-4:2002/kprA1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1870-4:2002/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 1870-4:2002/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1870-4:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 79.120.10
English Version
Safety of woodworking machines - Circular sawing machines -
Part 4: Multiblade rip sawing machines with manual loading
and/or unloading
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scies circulaires - Partie 4: Scies circulaires à déligner Kreissägemaschinen - Teil 4:
multilames à chargement et/ou déchargement manuel Mehrblattkreissägemaschinen für Längsschnitt mit
Handbeschickung und/oder Handentnahme
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1870-4:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-4:2001/prA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1870-4:2002/kprA1:2009
EN 1870-4:2001/prA1:2009 (E)
Contents Page
Foreword .3
1 Modification to the Foreword .4
2 Modification to Clause 1, Scope .4
3 Modification to Clause 2, Normative references .4
4 Modification to Clause 3, Terms and definitions .6
5 Modification to Clause 4, List of hazards .6
6 Modification to Clause 5, Safety requirements and/or measures (hanging paragraph) .8
7 Modification to 5.1.1, Safety and reliability of control systems .8
8 Modification to 5.1.3, Starting .9
9 Modification to 5.1.4, Normal stopping .9
10 Modification to 5.1.5, Emergency stop .
...