|
SIST EN 12653:2000/kprA2:2009
01-april-2009
Stroji za izdelavo obutve ter izdelkov iz usnja in njegovih imitacij - Žebljalniki -
Varnostne zahteve
Footwear, leather and imitation leather manufacturing machines - Nailing machines -
Safety requirements
Maschinen für die Herstellung von Schuhen aus Leder und Kunstleder - Nagelmaschinen
- Sicherheitsanforderungen
Machines pour la fabrication des chaussures et articles en cuir et en matériaux similaires
- Machines à clouer - Exigences de sécurité
Ta slovenski standard je istoveten z: EN 12653:1999/prA2
ICS:
61.060 Obuvala Footwear
SIST EN 12653:2000/kprA2:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12653:2000/kprA2:2009
---------------------- Page: 2 ----------------------
SIST EN 12653:2000/kprA2:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 12653:1999
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
January 2009
ICS 61.060
English Version
Footwear, leather and imitation leather manufacturing machines
- Nailing machines - Safety requirements
Machines pour la fabrication des chaussures et articles en Maschinen für die Herstellung von Schuhen aus Leder und
cuir et en matériaux similaires - Machines à clouer - Kunstleder - Nagelmaschinen - Sicherheitsanforderungen
Exigences de sécurité
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 201.
This draft amendment A2, if approved, will modify the European Standard EN 12653:1999. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12653:1999/prA2:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12653:2000/kprA2:2009
EN 12653:1999/prA2:2009 (E)
Foreword
This document (EN 12653:1999/prA2:2009) has been prepared by Technical Committee CEN/TC 201
“Leather and imitation leather goods and footwear manufacturing machinery - Safety”, the secretariat of which
is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
The first reason for amending the published standard EN 12653:1999 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards cited in the
Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
2
---------------------- Page: 4 ----------------------
SIST EN 12653:2000/kprA2:2009
EN 12653:1999/prA2:2009 (E)
1 Modification to the Foreword
th
Replace the 4 paragraph with the following: "For relationship with EU Directive(s), see informative Annexes
ZA and ZB, which are integral parts of this document."
2 Modification to the Introduction
Replace the complete text with the following:
"This document is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.".
3 Modification to Clause 1
th
In the 4 paragraph, replace "foreseeable misuse, component" with "foreseeable misuse and component".
Replace the last paragraph with the
...