|
SLOVENSKI STANDARD
01-september-2017
Železniške naprave - Preskušanje in simuliranje voznih karakteristik pri prevzemu
železniških vozil - Preskušanje obnašanja med vožnjo in mirovanjem
Railway applications - Testing and Simulation for the acceptance of running
characteristics of railway vehicles - Running Behaviour and stationary tests
Bahnanwendungen - Versuche und Simulationen für die Zulassung der fahrtechnischen
Eigenschaften von Eisenbahnfahrzeugen - Fahrverhalten und stationäre Versuche
Applications ferroviaires - Essais en vue de l'homologation du comportement dynamique
des véhicules ferroviaires - Essais en ligne et à poste fixe
Ta slovenski standard je istoveten z: EN 14363:2016/prA1
ICS:
45.060.01 Železniška vozila na splošno Railway rolling stock in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 14363:2016
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
June 2017
ICS 45.060.01
English Version
Railway applications - Testing and Simulation for the
acceptance of running characteristics of railway vehicles -
Running Behaviour and stationary tests
Applications ferroviaires - Essais et simulations en vue Bahnanwendungen - Versuche und Simulationen für
de l'homologation des caractéristiques dynamiques des die Zulassung der fahrtechnischen Eigenschaften von
véhicules ferroviaires - Comportement dynamique et Eisenbahnfahrzeugen - Fahrverhalten und stationäre
essais stationnaires Versuche
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 256.
This draft amendment A1, if approved, will modify the European Standard EN 14363:2016. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14363:2016/prA1:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
1 Modification to the Introduction . 5
2 Modifications in the whole document . 5
3 Modifications to Clause 3. 6
3.1 Modification to 3.11 . 6
3.2 Modification to 3.12 . 6
3.3 Modification to 3.13 . 6
4 Modification to Clause 5. 7
4.1 Modification to 5.3.1 . 7
4.2 Modification to 5.3.2, Note 1. 7
4.3 Modification to 5.3.2, last dash . 7
4.4 Modification to 5.3.3 . 7
4.5 Modification to 5.5 . 7
5 Modification to Clause 6. 7
st
5.1 Modification to 6.1.1 – Method 3, 1 paragraph. 7
5.2 Modification to 6.1.1, Note 5. 7
rd
5.3 Modification to 6.1.5.1.4, 3 paragraph . 8
nd
paragraph . 8
5.4 Modification to 6.1.5.1.5, 2
5.5 Modification to 6.1.5.1.8 . 8
6 Modifications to Clause 7. 8
6.1 Modification to 7.1 . 8
6.2 Modification to 7.2.1 . 8
6.3 Modification to 7.2.2, Table 1. 8
6.4 Modifications to 7.3.1 . 8
6.4.1 Table 2, Column Test zone 4 . 8
6.4.2 Table 2, Footnote f . 9
6.5 Modification to 7.4, Table 3 . 9
6.6 Modifications to 7.5.1, Table 4 . 9
6.7 Modifications to 7.5.1, Note 3. 9
6.8 Modification to 7.6.3.1, Table 5 (layout) . 9
6.9 Modification to 7.6.3.2.1 . 9
6.10 Modification to 7.6.3.2.5, Headline . 9
6.11 Modifications to 7.6.3.2.6 . 9
6.12 Modification to 7.6.3.2.6, Note 1 . 10
st
6.13 Modification to 7.6.3.2.7, 1 paragraph . 10
7 Modifications to Annex A . 10
7.1 Modification to Figure A.1 . 10
7.2 Modification to A.3 . 10
th
7.3 Modification to A.3, 4 paragraph . 10
7.4 Modification to A.3, Note below Figure A.4 . 10
7.5 Modification to A.7, first paragraph . 11
th
7.6 Modification to A.8.2, 4 paragraph . 11
7.7 Modification to A.8.2, last paragraph . 11
7.8 Modifications to A.8.4 . 11
th
7.9 Modification to A.9.2, 4 paragraph . 11
7.10 Modification A.9.2, last paragraph . 12
7.11 Modification to A.9.4.2 . 12
rd
7.12 Modification to A.9.4.4, 3 line from the end . 12
8 Modification to Annex D . 12
st
8.1 Modification to D.2.5.4, 1 formula . 12
8.2 Modification to D.2.4.5, Note . 12
9 Modification to Annex E. 13
9.1 Modification to E.2, Table E.1 . 13
rd
10 Modification to Figure I.1 (3 line, left column) . 13
11 Modification to Annex M . 13
11.1 Modification to Annex M.3, b) . 13
11.2 Modification to Annex M.3, Table M.2 . 13
12 Modification to Annex Q.2 . 13
13 Modification to Annex R . 13
st
13.1 Modification to R.1.1, 1 paragraph . 13
13.2 Modification to R.2, dashes . 13
13.3 Modification to R.5 . 13
rd
13.4 Modification to R.4., 3 paragraph . 14
13.5 Modifications to R.5 (x' and y not bold) . 14
13.6 Modifications to R.6 (p Italic) . 14
13.7 Modification to R.8.1, second dash . 15
14 Modification to Annex S . 15
14.1 Modification to S.2 . 15
14.2 Modification to S.4, second last line . 15
15 Modification to Annex T . 15
th st
15.1 Modification to Table T.1, 9 line, 1 and last column. 15
15.2 Modifications to T.3.3.4, Figure T.2 .
...