|
SIST EN 860:2009/kprA1:2009
01-april-2009
Varnost lesnoobdelovalnih strojev - Debelinski skobeljniki za enostransko
obdelavo
Safety of woodworking machines - One side thickness planing machines
Sicherheit von Holzbearbeitungsmaschinen - Dickenhobelmaschinen für einseitige
Bearbeitung
Sécurité des machines pour le travail du bois - Machines à raboter sur une face
Ta slovenski standard je istoveten z: EN 860:2007/prA1
ICS:
25.080.25 6WURML]DSORãþLQVNRREGHODYR Planing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 860:2009/kprA1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 860:2009/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 860:2009/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 860:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 79.120.10
English Version
Safety of woodworking machines - One side thickness planing
machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
raboter sur une face Dickenhobelmaschinen für einseitige Bearbeitung
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 860:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 860:2007/prA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 860:2009/kprA1:2009
EN 860:2007/prA1:2009 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Clause 2, Normative references .4
3 Modification to 5.4.5, Ergonomics and handling.4
4 Modification to 6.2, Marking .4
5 Modification to 6.3, Instruction handbook .4
6 Modification to Annex ZA .5
7 Addition of Annex ZB .6
2
---------------------- Page: 4 ----------------------
SIST EN 860:2009/kprA1:2009
EN 860:2007/prA1:2009 (E)
Foreword
This document (EN 860:2007/prA1:2009) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
3
---------------------- Page: 5 ----------------------
SIST EN 860:2009/kprA1:2009
EN 860:2007/prA1:2009 (E)
1 Modification to the Foreword
Replace the fifth paragraph with the
...