|
SIST EN 1317-5:2007+A1:2008/kFprA2:2011
01-november-2011
Oprema cest - 5. del: Zahteve za proizvode in ugotavljanje skladnosti za sisteme za
zadrževanje vozil
Road restraint systems - Part 5: Product requirements and evaluation of conformity for
vehicle restraint systems
Rückhaltesysteme an Straßen - Teil 5: Anforderungen an die Produkte,
Konformitätsverfahren und -bescheinigung für Fahrzeugrückhaltesysteme
Dispositifs de retenue routiers - Partie 5: Exigences relatives aux produits et évaluation
de la conformité pour les dispositifs de retenue des véhicules
Ta slovenski standard je istoveten z: EN 1317-5:2007+A1:2008/FprA2
ICS:
13.200 3UHSUHþHYDQMHQHVUHþLQ Accident and disaster control
NDWDVWURI
93.080.30 Cestna oprema in pomožne Road equipment and
naprave installations
SIST EN 1317- en,fr,de
5:2007+A1:2008/kFprA2:2011
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1317-5:2007+A1:2008/kFprA2:2011
---------------------- Page: 2 ----------------------
SIST EN 1317-5:2007+A1:2008/kFprA2:2011
EUROPEAN STANDARD
FINAL DRAFT
EN 1317-5:2007+A1:2008
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA2
September 2011
ICS 13.200; 93.080.30
English Version
Road restraint systems - Part 5: Product requirements and
evaluation of conformity for vehicle restraint systems
Dispositifs de retenue routiers - Partie 5: Exigences Rückhaltesysteme an Straßen - Teil 5: Anforderungen an
relatives aux produits et évaluation de la conformité pour die Produkte, Konformitätsverfahren und -bescheinigung für
les dispositifs de retenue pour véhicules Fahrzeugrückhaltesysteme
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 226.
This draft amendment A2, if approved, will modify the European Standard EN 1317-5:2007+A1:2008. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1317-5:2007+A1:2008/FprA2:2011:
worldwide for CEN national Members. E
---------------------- Page: 3 ----------------------
SIST EN 1317-5:2007+A1:2008/kFprA2:2011
EN 1317-5:2007+A1:2008/FprA2:2011(E)
Foreword
This document (EN 1317-5:2007+A1:2008/FprA2:2011) has been prepared by Technical Committee
CEN/TC 226 “Road equipment”, the secretariat of which is held by AFNOR.
This document is currently submitted to the UAP.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
2
---------------------- Page: 4 ----------------------
SIST EN 1317-5:2007+A1:2008/kFprA2:2011
EN 1317-5:2007+A1:2008/FprA2:2011(E)
1 Modification to the Introduction
Replace the existing introduction with the following:
“This document is a product standard for vehicle restraint systems placed on the market.
This document is designed for use in conjunction with Parts 1, 2, 3, ENV 1317 part 4 (to be replaced with
prEN 1317 part 4 and 7).
To ensure the full performance of road restraint systems in use, their production and installation is intended
to be controlled in accordance with this document.”
2 Modifications to Clause 2
Replace the reference:
“EN 10326, Continuously hot-dip zinc coated strip and sheet
...