EN 12312-16:2005/prA1

Aircraft ground support equipment - Specific requirements - Part 16: Air start equipment

EN 12312-16:2005/prA1

Name:EN 12312-16:2005/prA1   Standard name:Aircraft ground support equipment - Specific requirements - Part 16: Air start equipment
Standard number:EN 12312-16:2005/prA1   language:English language
Release Date:   technical committee:CEN/TC 274 - Aircraft ground support equipment
Drafting committee:CEN/TC 274/SC 3/WG 6 - Air start equipment   ICS number:49.100 - Ground service and maintenance equipment
SLOVENSKI STANDARD
SIST EN 12312-16:2005/kprA1:2008
01-november-2008
3RGSRUQDRSUHPDQDWOHK]DOHWDOVNLSURPHW3RVHEQH]DKWHYHGHO2SUHPD
]D]UDþQLSRJRQPRWRUMHY
Aircraft ground support equipment - Specific requirements - Part 16: Air start equipment
Luftfahrt-Bodengeräte - Besondere Anforderungen - Teil 16: Luftstartgeräte
Matériels au sol pour aéronefs - Exigences particulières - Partie 16: Matériel de
démarrage à air
Ta slovenski standard je istoveten z: EN 12312-16:2005/prA1
ICS:
49.100 Oprema za servis in Ground service and
vzdrževanje na tleh maintenance equipment
SIST EN 12312-16:2005/kprA1:2008 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 12312-16:2005/kprA1:2008

---------------------- Page: 2 ----------------------

SIST EN 12312-16:2005/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 12312-16:2005
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2008
ICS 49.100

English Version
Aircraft ground support equipment - Specific requirements - Part
16: Air start equipment
Matériels au sol pour aéronefs - Exigences particulières - Luftfahrt-Bodengeräte - Besondere Anforderungen - Teil
Partie 16: Matériel de démarrage à air 16: Luftstartgeräte
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 274.
This draft amendment A1, if approved, will modify the European Standard EN 12312-16:2005. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12312-16:2005/prA1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 12312-16:2005/kprA1:2008
EN 12312-16:2005/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Clause 1 .4
3 Modifications to Clause 2 .4
4 Modifications to 5.1.1 .4
5 Modification to 5.6.2 .4
6 Modification to Clause 7 .4
7 Addition of Annex ZB .5
8 Modification to the Bibliography.5

2

---------------------- Page: 4 ----------------------

SIST EN 12312-16:2005/kprA1:2008
EN 12312-16:2005/prA1:2008 (E)
Foreword
This document (EN 12312-16:2005/prA1:2008) has been prepared by Technical Committee CEN/TC 274
“Aircraft ground support equipment”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directives.
For relat
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27