EN 13042-3:2007/prA1

Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 3: IS machines

EN 13042-3:2007/prA1

Name:EN 13042-3:2007/prA1   Standard name:Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 3: IS machines
Standard number:EN 13042-3:2007/prA1   language:English language
Release Date:   technical committee:CEN/TC 151 - Construction equipment and building material machines - Safety
Drafting committee:CEN/TC 151/WG 13 - Machines and plants for the production, treatment and processing of flat, hollow and special glass - Safety   ICS number:81.100 - Equipment for the glass and ceramics industries
SLOVENSKI STANDARD
SIST EN 13042-3:2007/kprA1:2009
01-marec-2009
Stroji in obrati za proizvodnjo, obdelavo in predelavo votlega stekla - Varnostne
zahteve - 3. del: Stroji IS
Machines and plants for the manufacture, treatment and processing of hollow glass -
Safety requirements - Part 3: IS machines
Maschinen und Anlagen zur Herstellung, Be- und Verarbeitung von Hohlglas -
Sicherheitsanforderungen - Teil 3: IS-Maschinen
Machines et installations pour la production, le façonnage et la transformation du verre
creux - Exigences de sécurité - Partie 3: Machines IS
Ta slovenski standard je istoveten z: EN 13042-3:2007/prA1
ICS:
81.100 2SUHPD]DVWHNODUVNRLQ Equipment for the glass and
NHUDPLþQRLQGXVWULMR ceramics industries
SIST EN 13042-3:2007/kprA1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13042-3:2007/kprA1:2009

---------------------- Page: 2 ----------------------

SIST EN 13042-3:2007/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 13042-3:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
December 2008
ICS 81.100

English Version
Machines and plants for the manufacture, treatment and
processing of hollow glass - Safety requirements - Part 3: IS
machines
Machines et installations pour la production, le façonnage Maschinen und Anlagen zur Herstellung, Be- und
et la transformation du verre creux - Exigences de sécurité Verarbeitung von Hohlglas - Sicherheitsanforderungen -
- Partie 3: Machines IS Teil 3: IS-Maschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 13042-3:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13042-3:2007/prA1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13042-3:2007/kprA1:2009
EN 13042-3:2007/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Introduction.4
2 Modification to the Scope .4
3 Modification to Clause 2 .4
4 Modifications to Clause 4 .5
5 Modifications to Clause 5 .5
6 Modification to Clause 6 .6
7 Modifications to Clause 7 .7
8 Addition of Annex ZB .9
9 Modification to the Bibliography.9

2

---------------------- Page: 4 ----------------------

SIST EN 13042-3:2007/kprA1:2009
EN 13042-3:2007/prA1:2008 (E)
Foreword
This document (EN 13042-3:2007/prA1:2008
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27