|
SIST EN 14276-2:2007/kprA1:2010
01-november-2010
7ODþQDRSUHPD]DKODGLOQHVLVWHPHLQWRSORWQHþUSDONHGHO &HYRYRGL6SORãQH
]DKWHYH
Pressure equipment for refrigerating systems and heat pumps - Part 2: Piping - General
requirements
Druckgeräte für Kälteanlagen und Wärmepumpen - Teil 2: Rohrleitungen - Allgemeine
Anforderungen
Équipements sous pression pour systèmes de réfrigération et pompes à chaleur - Partie
2: Tuyauteries - Exigences générales
Ta slovenski standard je istoveten z: EN 14276-2:2007/FprA1
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
27.080 7RSORWQHþUSDONH Heat pumps
27.200 Hladilna tehnologija Refrigerating technology
SIST EN 14276-2:2007/kprA1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 14276-2:2007/kprA1:2010
---------------------- Page: 2 ----------------------
SIST EN 14276-2:2007/kprA1:2010
EUROPEAN STANDARD
FINAL DRAFT
EN 14276-2:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
August 2010
ICS 23.020.30; 27.080; 27.200
English Version
Pressure equipment for refrigerating systems and heat pumps -
Part 2: Piping - General requirements
Équipements sous pression pour systèmes de réfrigération Druckgeräte für Kälteanlagen und Wärmepumpen - Teil 2:
et pompes à chaleur - Partie 2: Tuyauteries - Exigences Rohrleitungen - Allgemeine Anforderungen
générales
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 182.
This draft amendment A1, if approved, will modify the European Standard EN 14276-2:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14276-2:2007/FprA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 14276-2:2007/kprA1:2010
EN 14276-2:2007/FprA1:2010 (E)
Contents Page
Foreword .3
1 Modification of Clause 2, Normative references .4
2 Modification of Clause 3, Terms, definitions, symbols, quantities and units .4
3 Modification to 4.1, General .4
4 Modification to 4.3.1.1 .5
5 Modification to 4.3.2, Special considerations .5
6 Modification to 4.4, Requirements for the prevention of brittle fracture .5
7 Modification to 4.5, Material documentation .5
8 Modification to 4.6, Materials for non-pressure retaining parts .5
9 Modification to 5.1, Category of piping .5
10 Modification to Table 3, Applicable requirements per piping type .5
11 Modification to 6.7, Design stress.6
12 Modification to 6.9.1, General .
...