|
SIST EN 13035-3:2004/kprA1:2009
01-april-2009
Stroji in obrati za proizvodnjo, obdelavo in predelavo ravnega stekla - Varnostne
zahteve - 3. del: Rezalniki
Machines and plants for the manufacture, treatment and processing of flat glass - Safety
requirements - Part 3: Cutting machines
Maschinen und Anlagen für die Herstellung, Be- und Verarbeitung von Flachglas -
Sicherheitsanforderungen - Teil 3: Schneidmaschinen
Machines et installations pour la production, le façonnage et la transformation du verre
plat - Exigences de sécurité - Partie 3: Machines à découper
Ta slovenski standard je istoveten z: EN 13035-3:2003/prA1
ICS:
81.100 2SUHPD]DVWHNODUVNRLQ Equipment for the glass and
NHUDPLþQRLQGXVWULMR ceramics industries
SIST EN 13035-3:2004/kprA1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13035-3:2004/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 13035-3:2004/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 13035-3:2003
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 81.100
English Version
Machines and plants for the manufacture, treatment and
processing of flat glass - Safety requirements - Part 3: Cutting
machines
Machines et installations pour la production, le façonnage Maschinen und Anlagen für die Herstellung, Be- und
et la transformation du verre plat - Exigences de sécurité - Verarbeitung von Flachglas - Sicherheitsanforderungen -
Partie 3: Machines à découper Teil 3: Schneidmaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 13035-3:2003. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13035-3:2003/prA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13035-3:2004/kprA1:2009
EN 13035-3:2003/prA1:2009 (E)
Contents Page
Foreword .3
1 Modification to the Introduction .4
2 Modifications to the Scope .4
3 Modifications to Clause 2 .4
4 Modification to Clause 3 .5
5 Modification to Clause 4 .6
6 Modifications to Clause 5 .6
7 Modification to Clause 6 .8
8 Modifications to Clause 7 .9
9 Addition of Annex K . 10
10 Modification to Annex ZA .
...