|
SIST EN 746-1:2000/kprA1:2009
01-april-2009
Industrijska termoprocesna oprema - 1. del: Splošne varnostne zahteve za
industrijsko termoprocesno opremo
Industrial thermoprocessing equipment - Part 1: Common safety requirements for
industrial thermoprocessing equipment
Industrielle Thermoprozessanlagen - Teil 1: Allgemeine Sicherheitsanforderungen an
industrielle Thermoprozessanlagen
Equipements thermiques industriels - Partie 1: Prescriptions générales de sécurité pour
les équipements thermiques industriels
Ta slovenski standard je istoveten z: EN 746-1:1997/prA1
ICS:
25.180.01 ,QGXVWULMVNHSHþLQDVSORãQR Industrial furnaces in general
SIST EN 746-1:2000/kprA1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 746-1:2000/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 746-1:2000/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 746-1:1997
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2009
ICS 25.180.01
English Version
Industrial thermoprocessing equipment - Part 1: Common safety
requirements for industrial thermoprocessing equipment
Equipements thermiques industriels - Partie 1: Industrielle Thermoprozessanlagen - Teil 1: Allgemeine
Prescriptions générales de sécurité pour les équipements Sicherheitsanforderungen an industrielle
thermiques industriels Thermoprozessanlagen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 186.
This draft amendment A1, if approved, will modify the European Standard EN 746-1:1997. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 746-1:1997/prA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 746-1:2000/kprA1:2009
EN 746-1:1997/prA1:2009 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Clause 2, Normative references .4
2.1 Basic Standards.4
2.2 Group Safety Standards.5
2.3 Product Safety Standards.7
3 Modification to Annex A.10
4 Modification to Annex ZB .11
2
---------------------- Page: 4 ----------------------
SIST EN 746-1:2000/kprA1:2009
EN 746-1:1997/prA1:2009 (E)
Foreword
This document (EN 746-1:1997/prA1:2009) has been prepared by Technical Committee CEN/TC 186
“Industrial thermoprocessing - Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationshi
...