|
SIST EN 15814:2011/kFprA1:2012
01-junij-2012
Bitumenske debeloslojne prevleke, modificirane s polimeri - Definicije in zahteve
Polymer modified bituminous thick coatings for waterproofing - Definitions and
requirements
Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung - Begriffe
und Anforderungen
Revêtements bitumineux épais modifiés aux polymères pour imperméabilisation -
Définitions et exigences
Ta slovenski standard je istoveten z: EN 15814:2011/FprA1
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
SIST EN 15814:2011/kFprA1:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 15814:2011/kFprA1:2012
---------------------- Page: 2 ----------------------
SIST EN 15814:2011/kFprA1:2012
EUROPEAN STANDARD
FINAL DRAFT
EN 15814:2011
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
April 2012
ICS 91.100.50
English Version
Polymer modified bituminous thick coatings for waterproofing -
Definitions and requirements
Revêtements bitumineux épais modifiés aux polymères Kunststoffmodifizierte Bitumendickbeschichtungen zur
pour imperméabilisation - Définitions et exigences Bauwerksabdichtung - Begriffe und Anforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 361.
This draft amendment A1, if approved, will modify the European Standard EN 15814:2011. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15814:2011/FprA1:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 15814:2011/kFprA1:2012
EN 15814:2011/FprA1:2012 (E)
Contents Page
Foreword .3
1 Modification to 3.4 .4
2 Modification to Table 1 .4
3 Modification to Clause 5 .4
4 Addition of Annex ZA . 11
2
---------------------- Page: 4 ----------------------
SIST EN 15814:2011/kFprA1:2012
EN 15814:2011/FprA1:2012 (E)
Foreword
This document (EN 15814:2011/FprA1:2012) has been prepared by Technical Committee CEN/TC 361
“Project Committee - Thick synthetic modified bitumous coating masses - Definitions and requirements/Test
methods”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
3
---------------------- Page: 5 ----------------------
SIST EN 15814:2011/kFprA1:2012
EN 15814:2011/FprA1:2012 (E)
1 Modification to 3.4
Change the text as follows:
"3.4
PMBC
Polymer Modified Bituminous thick Coating emulsion based, with or without admixtures, such as additives and
mineral aggregates, comprising of one or two components"
2 Modification to Table 1
a
Delete the footnote in the lines 4 and 5 of Table 1 a
...