EN 16185-1:2014/FprA1

Railway applications - Braking systems of multiple unit trains - Part 1: Requirements and definitions

EN 16185-1:2014/FprA1

Name:EN 16185-1:2014/FprA1   Standard name:Railway applications - Braking systems of multiple unit trains - Part 1: Requirements and definitions
Standard number:EN 16185-1:2014/FprA1   language:English language
Release Date:   technical committee:CEN/TC 256 - Railway applications
Drafting committee:CEN/TC 256/SC 3/WG 47 - Braking   ICS number:45.040 - Materials and components for railway engineering

SLOVENSKI STANDARD
SIST EN 16185-1:2015/oprA1:2017
01-junij-2017
Železniške naprave - Zavorni sistemi motornih vlakov - 1. del: Zahteve in definicije
Railway applications - Braking systems of multiple unit trains - Part 1: Requirements and
definitions
Bahnanwendungen - Bremssysteme für Triebzüge - Teil 1: Anforderungen und
Definitionen
Applications ferroviaires - Systèmes de freinage pour trains automoteurs - Partie 1 :
Exigences et définitions
Ta slovenski standard je istoveten z: EN 16185-1:2014/prA1
ICS:
45.040 Materiali in deli za železniško Materials and components
tehniko for railway engineering
SIST EN 16185-1:2015/oprA1:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

SIST EN 16185-1:2015/oprA1:2017

SIST EN 16185-1:2015/oprA1:2017

DRAFT
EUROPEAN STANDARD
EN 16185-1:2014
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
April 2017
ICS 45.040
English Version
Railway applications - Braking systems of multiple unit
trains - Part 1: Requirements and definitions
Applications ferroviaires - Systèmes de freinage pour Bahnanwendungen - Bremssysteme für Triebzüge -
trains automoteurs - Partie 1 : Exigences et définitions Teil 1: Anforderungen und Definitionen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 256.

This draft amendment A1, if approved, will modify the European Standard EN 16185-1:2014. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16185-1:2014/prA1:2017 E
worldwide for CEN national Members.

SIST EN 16185-1:2015/oprA1:2017
EN 16185-1:2014/prA1:2017 (E)
Contents Page
European foreword . 3
1 Modification to 3.16, maximum braking load . 4
2 Modification to Clause 6, Braking performance . 4
3 Modification to Annex ZA . 4

SIST EN 16185-1:2015/oprA1:2017
EN 16185-1:2014/prA1:2017 (E)
European foreword
This document (EN 16185-1:2014/prA1:2017) has been prepared by Technical Committee CEN/TC 256
“Railway applications”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
For relationship with EU Directive, see informative Annex ZA, which is an integral part of
EN 16185-1:2014.
SIST EN 16185-1:2015/oprA1:2017
EN 16185-1:2014/prA1:2017 (E)
1 Modification to 3.16, maximum braking load
Delete Note 1 to entry.
2 Modification to Clause 6, Braking performance
Add new subclause 6.2 after 6.1:
"6.2 Relevant load conditions
The brake performance calculation shall consider the following load conditions (as described in
EN 15663):
— minimum load: “design mass in working order”;
— normal load: “design mass under normal payload”;
— maximum braking load: load condition lower or equa
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27