|
SIST EN 12348:2000/kprA1:2008
01-december-2008
Stabilni vrtalni stroji - Varnost
Core drilling machines on stand - Safety
Kernbohrmaschinen auf Ständer - Sicherheit
Foreuses à béton (carotteuses) sur colonne - Sécurité
Ta slovenski standard je istoveten z: EN 12348:2000/prA1
ICS:
25.080.40 Vrtalniki Drilling machines
SIST EN 12348:2000/kprA1:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12348:2000/kprA1:2008
---------------------- Page: 2 ----------------------
SIST EN 12348:2000/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 12348:2000
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2008
ICS 25.080.40
English Version
Core drilling machines on stand - Safety
Foreuses à béton (carotteuses) sur colonne - Sécurité Kernbohrmaschinen auf Ständer - Sicherheit
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 12348:2000. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12348:2000/prA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12348:2000/kprA1:2008
EN 12348:2000/prA1:2008 (E)
Contents
Foreword.3
1 Modification to the Introduction.4
2 Modification to Clause 2, Normative references .4
3 Modifications to Clause 3, Terms and definitions.5
4 Modification to Clause 4, List of significant hazards.5
5 Modification to Clause 5, Safety requirements and/or measures.6
6 Modification to 5.1.2.1, Transmission parts.6
7 Modification to 5.1.2.2, Feed of the drilling unit on the column .6
8 Modification to 5.1.4, Stability during work .6
9 Modification to 5.1.5, Control device .7
10 Modification to 5.2.1, General.7
11 Modification to 5.2.2, Water pump .7
12 Modification to 5.4.2 .7
13 Modification to 5.4.3 .8
14 Modification to 5.4.4, Test method.8
15 Modification to 5.10.1, Noise reduction at the design stage .8
16 Modification to Clause 7, Information for use .
...