|
SLOVENSKI STANDARD
01-april-2017
9ODNQDWRFHPHQWQHUDYQHSORãþH6SHFLILNDFLMD]DL]GHOHNLQSUHVNXVQHPHWRGH
Fibre-cement flat sheets - Product specification and test methods
Faserzement-Tafeln - Produktspezifikation und Prüfverfahren
Plaques planes en fibres-ciment - Spécifications du produit et méthodes d'essai
Ta slovenski standard je istoveten z: EN 12467:2012+A1:2016/prA2
ICS:
91.100.40 &HPHQWQLL]GHONLRMDþDQL] Products in fibre-reinforced
YODNQL cement
SIST EN en,fr,de
12467:2013+A1:2016/oprA2:2017
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 12467:2012+A1:2016
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
February 2017
ICS 91.100.40
English Version
Fibre-cement flat sheets - Product specification and test
methods
Plaques planes en fibres-ciment - Spécifications du Faserzement-Tafeln - Produktspezifikation und
produit et méthodes d'essai Prüfverfahren
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 128.
This draft amendment A2, if approved, will modify the European Standard EN 12467:2012+A1:2016. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12467:2012+A1:2016/prA2:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Modification to the whole document . 4
2 Modification to Clause 5.1.1, Composition . 4
3 Modification to Clause 6.2.1, General . 4
4 Modification to Clause 6.3.5, Continuous surveillance of FPC . 4
5 Modification to Annex ZA (informative), Relationship of this European Standard with
Regulation (EU) No.305/2011 . 4
European foreword
This document (EN 12467:2012+A1:2016/prA1:2017) has been prepared by Technical Committee
CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the
secretariat of which is held by NBN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
1 Modification to the whole document
Replace in the whole document the terms “production method”, “method of manufacture” and
“production process” by “manufacturing process”.
2 Modification to Clause 5.1.1, Composition
Replace the last sentence of the first paragraph with the following sentence:
"The cement shall comply with EN 197-1 or an agreed technical specification relevant in the country of
use provided the cement compound composition is in accordance with EN 197-1.".
3 Modification to Clause 6.2.1, General
Add as 3rd paragraph of 6.2.1 the following text:
“Testing of mechanical characteristics is normally carried out with the upper face in compression. If
required to establish a relationship between upper and under face testing where significant differences
are expected or if required for design purposes, the load shall be applied on the under face. Results
obtained for under face testing are not relevant for classification.”.
4 Modification to Clause 6.3.5, Continuous surveillance of FPC
Add the following sentence to the 1st paragraph:
"The significance of any changes shall be assessed.".
5 Modification to Annex ZA (informative), Relationship of this European
Standard with Regulation (EU) No.305/2011
Replace Annex ZA (including change in title) with the following:
"
Annex ZA
(informative)
Relationship of this European Standard with Regulation [EU] No.305/2011
(When applying this standard as a harmonized standard under Regulation [EU] No. 305/2011,
manufacturers and Member States are obliged by this regulation to use this Annex)
ZA.1 Scope and relevant characteristics
This European Standard has been prepared under standardization request M/121 “Internal and
external wall and ceiling finishes” given to CEN and CENELEC by the European Commission (EC) and
the European Free Trade Association (EFTA).
When this European Standard is cited in the Official Journal of the European Union (OJEU
...