|
oSIST prEN 10249-2:2006
01-junij-2006
Hladno oblikovane zagate iz nelegiranih jekel - 2. del: Mejni odstopki mer in
tolerance oblik
Cold formed steel sheet piling - Part 2: Tolerances on shape and dimensions
Kaltgeformte Spundbohlen aus unlegierten Stählen - Teil 2: Grenzabmaße und
Formtoleranzen
Palplanches formées a froid en acier - Partie 2 : Tolérances sur les dimensions et les
formes
Ta slovenski standard je istoveten z: prEN 10249-2
ICS:
77.140.45 Nelegirana jekla Non-alloyed steels
77.140.70 Jekleni profili Steel profiles
oSIST prEN 10249-2:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 10249-2:2006
---------------------- Page: 2 ----------------------
oSIST prEN 10249-2:2006
EUROPEAN STANDARD
DRAFT
prEN 10249-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2006
ICS 77.140.70 Will supersede EN 10249-2:1995
English Version
Cold formed steel sheet piling - Part 2: Tolerances on shape and
dimensions
Palplanches formées à froid en acier - Partie 2 : Tolérances
sur les dimensions et les formes
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ECISS/TC 10.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10249-2:2006: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10249-2:2006
prEN 10249-2:2006 (E)
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Control of tolerances - General .4
4 Height of profiles .4
5 Width of profiles.5
6 Wall thickness of profiles .5
7 Straightness of profiles.5
7.1 General.5
7.2 Bending.5
7.3 Curving .6
7.4 Twisting .7
8 Length .8
9 Squareness of ends.8
10 Angular deviation.9
11 Mass of profiles.9
12 Joints, overlapping.9
13 Options .10
2
---------------------- Page: 4 ----------------------
oSIST prEN 10249-2:2006
prEN 10249-2:2006 (E)
Foreword
This document (prEN 10249-2:2006) has been prepared by Technical Committee ECISS/TC 10 “Structural
steels - Grades and qualities”, the secretariat of which is held by NEN.
This document is currently submitted
...