|
SLOVENSKI STANDARD
01-januar-2023
Nadomešča:
SIST EN ISO 1179-2:2014
Priključki za splošno uporabo in za fluidno tehniko - Odprtine in priključki z navoji
po ISO 228-1 z elastomernim ali kovinskim tesnjenjem - 2. del: Zelo obremenjeni
ravni priključki (vrsta S) in malo obremenjeni ravni priključki (vrsta L) z
elastomernim tesnjenjem (tip E) (ISO 1179-2:2022)
Connections for general use and fluid power - Ports and stud ends with ISO 228-1
threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and
light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2022)
Leitungsanschlüsse für allgemeine Anwendung und Fluidtechnik - Einschraublöcher und
Einschraubzapfen mit Gewinde nach ISO 228-1 und Elastomerdichtung oder metallener
Dichtkante - Teil 2: Einschraubzapfen mit Elastomerdichtung (Form E), schwere (S) und
leichte Reihe (L) (ISO 1179-2:2022)
Raccordements pour applications générales et transmissions hydrauliques et
pneumatiques - Orifices et éléments mâles à filetage ISO 228-1 à joint en élastomère ou
étanchéité métal sur métal - Partie 2: Éléments mâles de séries légère (série L) et lourde
(série S) avec joint en élastomère (type E) (ISO 1179-2:2022)
Ta slovenski standard je istoveten z: EN ISO 1179-2:2022
ICS:
23.100.40 Cevna napeljava in sklopke Piping and couplings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 1179-2
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 23.100.40 Supersedes EN ISO 1179-2:2013
English Version
Connections for general use and fluid power - Ports and
stud ends with ISO 228-1 threads with elastomeric or
metal-to-metal sealing - Part 2: Heavy-duty (S series) and
light-duty (L series) stud ends with elastomeric sealing
(type E) (ISO 1179-2:2022)
Raccordements pour applications générales et Leitungsanschlüsse für allgemeine Anwendung und
transmissions hydrauliques et pneumatiques - Orifices Fluidtechnik - Einschraublöcher und Einschraubzapfen
et éléments mâles à filetage ISO 228-1 à joint en mit Gewinde nach ISO 228-1 und Elastomerdichtung
élastomère ou étanchéité métal sur métal - Partie 2: oder metallener Dichtkante - Teil 2: Einschraubzapfen
Éléments mâles de séries légère (série L) et lourde mit Elastomerdichtung (Form E), schwere (S) und
(série S) avec joint en élastomère (type E) (ISO 1179- leichte Reihe (L) (ISO 1179-2:2022)
2:2022)
This European Standard was approved by CEN on 13 November 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1179-2:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 1179-2:2022) has been prepared by Technical Committee ISO/TC 131 "Fluid
power systems" in collaboration with Technical Committee CEN/TC 459/SC 10 “Steel tubes, and iron
and steel fittings” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1179-2:2013.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 1179-2:2022 has been approved by CEN as EN ISO 1179-2:2022 without any
modification.
INTERNATIONAL ISO
STANDARD 1179-2
Third edition
2022-11
Connections for general use and fluid
power — Ports and stud ends with
ISO 228-1 threads with elastomeric or
metal-to-metal sealing —
Part 2:
Heavy-duty (S series) and light-duty
(L series) stud ends with elastomeric
sealing (type E)
Raccordements pour applications générales et transmissions
hydrauliques et pneumatiques — Orifices et éléments mâles à filetage
ISO 228-1 à joint en élastomère ou étanchéité métal sur métal —
Partie 2: Éléments mâles de séries légère (série L) et lourde (série S)
avec joint en élastomère (type E)
Reference number
ISO 1179-2:2022(E)
ISO 1179-2:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
ISO 1179-2:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Interchangeability warning .2
5 Dimensions .2
6 Elastomeric seals .3
7 Requirements . 5
7.1 Working pressure . 5
7.2 Performance . 5
8 Designation of stud ends and elastomeric seals . 6
8.1 Stud ends . . 6
8.2 Elastomeric seals . 6
9 Identification statement (reference to this document) . 7
Bibliography . 8
iii
ISO 1179-2:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee
SC 4, Connectors and similar products and components, in collaboration with the European Committee
for Standardization (CEN) Technical Committee CEN/TC 459, ECISS - European Committee for Iron and
Steel Standardization, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 1179-2:2013), which has been technically
revised.
The main changes are as follows:
— Clause 4, Interchangeability warning, concerning the hazards of intermixing of stud ends with
various port types, has been added;
— material requirements for elastomeric seal have been added;
— test methods, test report and re-use of components have been replaced with the equivalent
requirements of ISO 19879;
— Figures 1 and 2 have been redrawn;
— the tables have been renumbered to the order in which they are cited in the text (Table 2 to Table 1,
Table 4 to Table 2, Table 3 remains the same, Table 5 to Table 4, Table 1 to Table 5);
— Annex A and the references to the annex have been deleted;
A list of all parts in the ISO 1179 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO 1179-2:2022(E)
Introduction
In fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under
pressure within a circ
...