|
SLOVENSKI STANDARD
01-januar-2023
Hlapni proizvodi - Ugotavljanje mase izhlapele e-tekočine in mase zbranega
aerosola (ISO 24197:2022)
Vapour products - Determination of e-liquid vaporised mass and aerosol collected mass
(ISO 24197:2022)
Dampfprodukte- Bestimmung verdampfter E-Liquid-Masse und gesammelter
Aerosolmasse (ISO 24197:2022)
Produits de vapotage - Détermination de la masse de e-liquide vaporisé et de la masse
d’aérosol collecté (ISO 24197:2022)
Ta slovenski standard je istoveten z: EN ISO 24197:2022
ICS:
65.160 Tobak, tobačni izdelki in Tobacco, tobacco products
oprema and related equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 24197
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 65.160
English Version
Vapour products - Determination of e-liquid vaporised
mass and aerosol collected mass (ISO 24197:2022)
Produits de vapotage - Détermination de la masse de e- Dampfprodukte- Bestimmung verdampfter E-Liquid-
liquide vaporisé et de la masse d'aérosol collecté Masse und gesammelter Aerosolmasse (ISO/FDIS
(ISO/FDIS 24197:2022) 24197:2022)
This European Standard was approved by CEN on 14 November 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24197:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 24197:2022) has been prepared by Technical Committee ISO/TC 126 "Tobacco
and tobacco products" in collaboration with Technical Committee CEN/TC 437 “Electronic cigarettes
and e-liquids” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 24197:2022 has been approved by CEN as EN ISO 24197:2022 without any modification.
INTERNATIONAL ISO
STANDARD 24197
First edition
2022-11
Vapour products — Determination of
e-liquid vaporised mass and aerosol
collected mass
Produits de vapotage — Détermination de la masse de e-liquide
vaporisé et de la masse d’aérosol collecté
Reference number
ISO 24197:2022(E)
ISO 24197:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
ISO 24197:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Procedure .2
6.1 General . 2
6.2 Preparation . 2
6.2.1 Vapour products . 2
6.2.2 Filter pad handling . 2
6.2.3 Aerosol trapping . 3
6.2.4 Puff volume check . 3
6.2.5 Handling of aerosol samples . 3
6.3 Determination of e-liquid vaporised mass (EVM) . 3
6.4 Determination of aerosol collected mass (ACM) . 3
6.5 Specific mass determination of puff blocks . 4
7 Repeatability and reproducibility .5
7.1 General . 5
7.2 Results from the interlaboratory study 2015 (Study 1) . 5
7.3 Results from the interlaboratory study 2019 (Study 2) . 6
8 Test report . 6
Annex A (informative) Trapping efficiency . 9
Annex B (normative) Glass fibre filter pad specifications.10
Bibliography .11
iii
ISO 24197:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 126, Tobacco and tobacco products,
Subcommittee SC 3, Vape and vapour products, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 437, Electronic cigarettes and related e-liquids, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO 24197:2022(E)
Introduction
Technical investigation of vapour products requires determining aerosol collected mass (ACM) and
e-liquid vaporized mass (EVM) measurements in emissions. Therefore, there is a necessity to have an
International Standard in place to get reliable/comparable data on ACM and EVM in electronic cigarette
emissions.
[1]
The method in this document is based upon the CORESTA recommended method (CRM) 84, which
[2]
was written on the basis of the results obtained from interlaboratory studies conducted in 2015 and
[3]
2019 involving 18 and 11 laboratories, respectively.
This document has been developed to describe the procedures used to measure the amount of ACM
and EVM in the aerosol from vapour products utilizing a gravimetric method. The experimental design
[4][5]
parameters used to collect the aerosolised vapour should be evaluated and documented for each
analysis.
v
----------------
...