|
SLOVENSKI STANDARD
01-november-2016
,QGXVWULMVNLYHQWLOL7UGQRVWRKLãMDGHO 0HWRGD]DL]UDþXQRKLãLMNRYLQVNLK
YHQWLORYNLQLVRL]MHNOD'RSROQLOR$
Industrial valves - Shell design strength - Part 4: Calculation method for valve shells
manufactured in metallic materials other than steel
Industriearmaturen - Gehäusefestigkeit - Teil 4: Berechnungsverfahren für drucktragende
Gehäuse von Armaturen aus anderen metallischen Werkstoffen als Stahl
Robinetterie industrielle - Résistance mécanique des enveloppes - Partie 4: Méthode de
calcul relative aux enveloppes d'appareils de robinetterie en matériaux métalliques
autres que l'acier
Ta slovenski standard je istoveten z: EN 12516-4:2014/prA1
ICS:
23.060.01 Ventili na splošno Valves in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 12516-4:2014
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
November 2016
ICS 23.060.01
English Version
Industrial valves - Shell design strength - Part 4:
Calculation method for valve shells manufactured in
metallic materials other than steel
Robinetterie industrielle - Résistance mécanique des Industriearmaturen - Gehäusefestigkeit - Teil 4:
enveloppes - Partie 4 : Méthode de calcul relative aux Berechnungsverfahren für drucktragende Gehäuse von
enveloppes d'appareils de robinetterie en matériaux Armaturen aus anderen metallischen Werkstoffen als
métalliques autres que l'acier Stahl
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 69.
This draft amendment A1, if approved, will modify the European Standard EN 12516-4:2014. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12516-4:2014/prA1:2016 E
worldwide for CEN national Members.
EN 12516-4:2014/prA1:2016 (E)
Contents Page
European foreword . 3
1 Modification to 5.2.3, Pressure/temperature ratings for cast iron . 4
2 Modification to 5.5.2, Materials other than aluminium . 4
3 Modification to Annex ZA (informative), Relationship between this European
Standard and the Essential Requirements of EU Directive 97/23/EC (PED) . 5
EN 12516-4:2014/prA1:2016 (E)
European foreword
This document (EN 12516-4:2014/prA1:2016) has been prepared by Technical Committee CEN/TC 69
“Industrial valves”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
T
...