|
SLOVENSKI STANDARD
01-februar-2023
Nadomešča:
SIST EN ISO 1522:2007
Barve in laki - Preskus trdote z dušenjem nihanja (ISO 1522:2022)
Paints and varnishes - Pendulum damping test (ISO 1522:2022)
Beschichtungsstoffe - Pendeldämpfungsprüfung (ISO 1522:2022)
Peintures et vernis - Essai d'amortissement du pendule (ISO 1522:2022)
Ta slovenski standard je istoveten z: EN ISO 1522:2022
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 1522
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 1522:2006
English Version
Paints and varnishes - Pendulum damping test (ISO
1522:2022)
Peintures et vernis - Essai d'amortissement du pendule Beschichtungsstoffe - Pendeldämpfungsprüfung (ISO
(ISO 1522:2022) 1522:2022)
This European Standard was approved by CEN on 12 November 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1522:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 1522:2022) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1522:2006.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 1522:2022 has been approved by CEN as EN ISO 1522:2022 without any modification.
INTERNATIONAL ISO
STANDARD 1522
Fourth edition
2022-11
Paints and varnishes — Pendulum
damping test
Peintures et vernis — Essai d'amortissement du pendule
Reference number
ISO 1522:2022(E)
ISO 1522:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
ISO 1522:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 S c op e . 1
2 Nor m at i ve r ef er enc e s . 1
3 Terms and definitions . 1
4 P r i nc iple . 1
5 A pp a r at u s . 1
6 S a mpl i n g . 4
7 Te s t p a nel s .4
7.1 S ubstrate . 4
7.2 P reparation and coating . 4
7.3 D rying and conditioning . 4
7.4 T hickness of coating . 4
8 P r o c e du re .4
8.1 C alibration of the instruments . 4
8.2 Ambient conditions. 5
8.3 D etermination of pendulum damping time . 5
9 E xpression of results . 5
10 P r e c i s ion . 5
10 .1 K ön i g p endu lu m . 5
10.1.1 G eneral . 5
10.1.2 Repeatability limit, r . 5
10.1.3 Reproducibility limit, R. 5
10.2 Persoz pendulum . 6
10.2.1 Repeatability limit, r . 6
10.2.2 R eproducibility limit, R. 6
11 Supplementary test conditions .6
12 Te s t r ep or t . 6
Annex A (normative) Calibration of the König pendulum. 8
Annex B (normative) Calibration of the Persoz pendulum . 9
Bibliography .10
iii
ISO 1522:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 1522:2006), which has been technically
revised.
The main changes are as follows:
— Clause 3 “Terms and definitions” has been added.
— The recommendation of using metal or glass panels has been removed from 7.1 because the test
method is also usable for other substrate materials, e.g. plastics.
...