EN 1870-17:2007/FprA2

Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws)

Name：EN 1870-17:2007/FprA2   Standard name：Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws) Standard number：EN 1870-17:2007/FprA2   language：English language Release Date：   technical committee：CEN/TC 142 - Woodworking machines - Safety Drafting committee：CEN/TC 142/WG 4 - Circular sawing machines   ICS number：79.120.10 - Woodworking machines

SLOVENSKI STANDARD
SIST EN 1870-17:2007/kFprA2:2009
01-junij-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY.URåQHåDJHGHO5RþQLNRQ]ROQLþHOLOQLN]
HQLPDJUHJDWRPURþQHUDGLDOQHåDJH
Safety of woodworking machines - Circular sawing machines - Part 17: Manual
horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws)
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 17:
Handbetätigte waagerecht schneidende Auslegerkreissägemaschinen mit einem
Sägeaggregat (handbetätigte Radialsägen)
Sécurité des machines pour le travail du bois - Machines à scier circulaires - Partie 17:
Tronçonneuses manuelles à coupe horizontale avec une unité de sciage (scies
circulaires radiales manuelles)
Ta slovenski standard je istoveten z: EN 1870-17:2007/FprA2
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870-17:2007/kFprA2:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1870-17:2007/kFprA2:2009

---------------------- Page: 2 ----------------------

SIST EN 1870-17:2007/kFprA2:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1870-17:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA2
April 2009
ICS 79.120.10

English Version
Safety of woodworking machines - Circular sawing machines -
Part 17: Manual horizontal cutting cross-cut sawing machines
with one saw unit (manual radial arm saws)
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scier circulaires - Partie 17: Tronçonneuses manuelles à Kreissägemaschinen - Teil 17: Handbetätigte waagerecht
coupe horizontale avec une unité de sciage (scies schneidende Auslegerkreissägemaschinen mit einem
circulaires radiales manuelles) Sägeaggregat (handbetätigte Radialsägen)
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A2, if approved, will modify the European Standard EN 1870-17:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved R
...