|
SLOVENSKI STANDARD
01-julij-2022
Nadomešča:
SIST-TS CEN/TS 14541:2013
Polimerne cevi in fitingi - Uporaba recikliranih plastomerov - 1. del: Terminologija
Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary
Kunststoff-Rohrleitungen und -Formstücke - Verwendung von thermoplastischen
Rezyklaten - Teil 1: Begriffe
Tubes et raccords en plastique - Utilisation de recyclats thermoplastiques - Partie 1 :
Vocabulaire
Ta slovenski standard je istoveten z: EN 14541-1:2022
ICS:
01.040.23 Tekočinski sistemi in sestavni Fluid systems and
deli za splošno rabo (Slovarji) components for general use
(Vocabularies)
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 14541-1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2022
EUROPÄISCHE NORM
ICS 83.140.30 Supersedes CEN/TS 14541:2013
English Version
Plastics pipes and fittings - Utilisation of thermoplastics
recyclates - Part 1: Vocabulary
Tubes et raccords en plastique - Utilisation de recyclats Kunststoff-Rohrleitungen und -Formstücke -
thermoplastiques - Partie 1 : Vocabulaire Verwendung von thermoplastischen Rezyklaten - Teil
1: Begriffe
This European Standard was approved by CEN on 7 February 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14541-1:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Abbreviations . 8
Bibliography . 9
European foreword
This document (EN 14541-1:2022) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2022, and conflicting national standards shall
be withdrawn at the latest by November 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document, together with Part 2 of the EN 14541 series, supersedes CEN/TS 14541:2013.
This document is part of the new EN 14541 series, which will consist of the following parts under the
general title Plastics pipes and fittings - Utilisation of thermoplastics recyclates:
a) Part 1: Vocabulary (this document);
b) Part 2: Recommendations for relevant characteristics.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
Introduction
The EN 14541 series is intended to give recommendations to the value chain of thermoplastics piping
systems to stimulate the use of thermoplastics recyclates (e.g. PVC-U, PVC-C, PE, PP, and ABS) as defined
in the European circular economy policy.
This part of the EN 14541 series defines the relevant terms and definitions related to the use of
thermoplastics recyclates in thermoplastics pipes and fittings. The commonly used terms and definitions
are reviewed, and as much as possible aligned with the practises within the thermoplastics pipes and
fittings value chain and the vocabulary used in European policy documents (e.g. circular economy,
sustainability) and existing international standards.
Part 2 is a CEN/TS document in which recommendations are given about the relevant characteristics for
defining (e.g. fingerprinting) commonly used thermoplastics recyclates intended to be used in
thermoplastics pipes and fittings.
NOTE These characteristics are intended for use within an agreed specification.
CEN/TC 249 “Plastics” developed a series of CEN publications on “Plastics Recycling” which consists of:
EN 15343 [1], EN 15344 [2], EN 15345 [3], EN 15346 [4], CEN/TS 16010 [5] and CEN/TS 16011 [6].
Other documents that discuss recycling are e.g. ISO 15270 [7] and Waste Framework Directive [8].
1 Scope
This document specifies the general terms and definitions relevant for the utilization of thermoplastics
recyclates in thermoplastics pipes, fittings and ancillaries for both pressure and non-pressure piping
systems.
This document is intended to be used by specification writers in conjunction
...