|
SIST EN 12629-5-2:2004/kFprA1:2010
01-april-2010
6WURML]DL]GHODYRJUDGEHQLKSURL]YRGRYL]EHWRQDLQDSQHQHJDSHãþHQFD9DUQRVW
GHO 6WURML]DL]GHODYRFHYLSRYRGRUDYQLRVL
Machines for the manufacture of constructional products from concrete and calcium-
silicate - Safety - Part 5-2: Pipe making machines manufacturing in the horizontal axis
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen -
Sicherheit - Teil 5-2: Beton-Rohrmaschinen mit Fertigung in horizontaler Lage
Machines pour la fabrication de produits de construction en béton et silico-calcaire -
Sécurité - Partie 5-2: Machines pour la fabrication de tuyaux dans l'axe horizontal
Ta slovenski standard je istoveten z: EN 12629-5-2:2003/FprA1
ICS:
91.220 Gradbena oprema Construction equipment
SIST EN 12629-5-2:2004/kFprA1:2010 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12629-5-2:2004/kFprA1:2010
---------------------- Page: 2 ----------------------
SIST EN 12629-5-2:2004/kFprA1:2010
EUROPEAN STANDARD
FINAL DRAFT
EN 12629-5-2:2003
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2010
ICS 91.220
English Version
Machines for the manufacture of constructional products from
concrete and calcium-silicate - Safety - Part 5-2: Pipe making
machines manufacturing in the horizontal axis
Machines pour la fabrication de produits de construction en Maschinen für die Herstellung von Bauprodukten aus Beton
béton et silico-calcaire - Sécurité - Partie 5-2: Machines und Kalksandsteinmassen - Sicherheit - Teil 5-2: Beton-
pour la fabrication de tuyaux dans l'axe horizontal Rohrmaschinen mit Fertigung in horizontaler Lage
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 12629-5-2:2003. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12629-5-2:2003/FprA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12629-5-2:2004/kFprA1:2010
EN 12629-5-2:2003/FprA1:2010 (E)
Contents Page
Foreword .3
1 Modifications to the Foreword .4
2 Modifications to the Introduction .4
3 Modifications to Clause 1 (Scope) .5
4 Modifications to Clause 2 (Normative references) .5
5 Modifications to Clause 3 (Terms and definitions) .6
6 Modifications to Clause 4 (List of significant hazards) .6
7 Modifications to Clause 5 (Safety requirements and/or measures) .6
8 Modifications to Clause 6 (Verification of safety requirements and/or measures) .7
9 Modifications to Clause 7 (Information for use) .7
10 Modifications to Clause 8 (
...