|
SIST EN 1870-11:2004/kprA1:2009
01-maj-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY.URåQHåDJHGHO 3RODYWRPDWVNLLQ
DYWRPDWVNLNRQ]ROQLþHOLOQLN]HQLPDJUHJDWRP
Safety of woodworking machines - Circular sawing machines - Part 11: Semi-automatic
and automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws)
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 11:
Halbautomatische und automatische waagerecht schneidende
Auslegerkreissägemaschinen mit einem Sägeaggregat (Radialsägen)
Sécurité des machines pour le travail du bois - Machines à scier circulaires - Partie 11:
Tronçonneuses automatiques et semi-automatiques à coupe horizontale (scies
circulaires radiales)
Ta slovenski standard je istoveten z: EN 1870-11:2003/prA1
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870-11:2004/kprA1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1870-11:2004/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 1870-11:2004/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1870-11:2003
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2009
ICS 79.120.10
English Version
Safety of woodworking machines - Circular sawing machines -
Part 11: Semi-automatic and automatic horizontal cross-cut
sawing machines with one saw unit (radial arm saws)
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scier circulaires - Partie 11: Tronçonneuses automatiques Kreissägemaschinen - Teil 11: Halbautomatische und
et semi-automatiques à coupe horizontale (scies circulaires automatische waagrecht schneidende
radiales) Auslegerkreissägemaschinen mit einem Sägeaggregat
(Radialsägen)
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1870-11:2003. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-11:2003/prA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1870-11:2004/kprA1:2009
EN 1870-11:2003/prA1:2009 (E)
Contents Page
Foreword .3
1 Modification to the Foreword .4
2 Modification to Clause 1, Scope .4
3 Modification to Clause 2, Normative references .4
4 Modification to Clause 3, Terms and definitions .6
5 Modification to Clause 4, List of significant hazards .6
6 Modification to 5.1, General .8
7 Modification to 5.2.1, Safety and reliability of control systems .8
8 Modification to 5.2.3, Starting .9
9 Modification to 5.2.4, Normal stopping .
...