EN ISO 21646:2022

Solid recovered fuels - Sample preparation (ISO 21646:2022)

EN ISO 21646:2022

Name:EN ISO 21646:2022   Standard name:Solid recovered fuels - Sample preparation (ISO 21646:2022)
Standard number:EN ISO 21646:2022   language:English language
Release Date:17-May-2022   technical committee:CEN/TC 343 - Solid Recovered Fuels
Drafting committee:CEN/TC 343/WG 3 - Sampling, sample reduction and supplementary test methods   ICS number:75.160.10 - Solid fuels

SLOVENSKI STANDARD
01-julij-2022
Nadomešča:
SIST EN 15413:2011
SIST EN 15443:2011
Trdna alternativna goriva - Priprava vzorca (ISO 21646:2022)
Solid recovered fuels - Sample preparation (ISO 21646:2022)
Feste Sekundärbrennstoffe - Probenvorbereitung (ISO 21646:2022)
Combustibles solides de récupération - Préparation des échantillons (ISO 21646:2022)
Ta slovenski standard je istoveten z: EN ISO 21646:2022
ICS:
75.160.10 Trda goriva Solid fuels
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 21646
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2022
EUROPÄISCHE NORM
ICS 75.160.10 Supersedes EN 15443:2011, EN 15413:2011
English Version
Solid recovered fuels - Sample preparation (ISO
21646:2022)
Combustibles solides de récupération - Préparation des Feste Sekundärbrennstoffe - Probenvorbereitung (ISO
échantillons (ISO 21646:2022) 21646:2022)
This European Standard was approved by CEN on 25 March 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21646:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 21646:2022) has been prepared by Technical Committee ISO/TC 300 "Solid
recovered materials, including solid recovered fuels" in collaboration with Technical Committee
CEN/TC 343 “Solid recovered materials, including solid recovered fuels” the secretariat of which is held
by SFS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2022, and conflicting national standards
shall be withdrawn at the latest by November 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15443:2011 and EN 15413:2011.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 21646:2022 has been approved by CEN as EN ISO 21646:2022 without any modification.

INTERNATIONAL ISO
STANDARD 21646
First edition
2022-05
Solid recovered fuels — Sample
preparation
Combustibles solides de récupération — Préparation des échantillons
Reference number
ISO 21646:2022(E)
ISO 21646:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
ISO 21646:2022(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 4
5 Safety remarks . 4
6 Principles of correct sample preparation . 4
7 Quality control and sources of error .6
8 Apparatus . 7
8.1 Selection of equipment . 7
8.2 Apparatus for sample division . 8
8.2.1 Scoops and shovels (sampling tools) . 8
8.2.2 Riffle boxes . 9
8.2.3 Rotary sample dividers . 10
8.3 Apparatus for particle size reduction . 11
8.3.1 Shredder . 11
8.3.2 Coarse cutting mill . 11
8.3.3 Cutting mill . 11
8.4 Sieves . 11
8.5 Balance . 11
9 Sample preparation procedure .12
9.1 General .12
9.2 Step 1: Collecting the relevant information of the material for sample preparation .12
9.3 Step 2: Making a sample preparation plan .12
9.3.1 General .12
9.3.2 Sample division . . .12
9.3.3 Particle size reduction of a sample .12
9.3.4 Retaining the minimum (sub-)sample mass . 15
9.4 Step 3: Performing the sample preparation plan . 16
10 Methods for homogenization and sample division .16
10.1 General . 16
10.2 Homogenization. 16
10.3 Sample division methods . 16
10.3.1 General . 16
10.3.2 Riffling . 16
10.3.3 Strip division . . 17
10.3.4 Long strip . 18
10.3.5 Manual increment division . 18
10.3.6 Rotary sample divider . 19
10.3.7 Fractional shovelling . 19
10.3.8 Quartering . 20
11 Methods for mass and particle size reduction of laboratory samples and general
analysis samples .21
11.1 General . 21
11.2 Initial sample division . 21
11.3 Initial mass determination . 21
11.4 Pre-drying .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27