|
SIST EN 14656:2007/kFprA1:2009
01-november-2009
Varnost strojev - Varnostne zahteve za stiskalnice za iztiskanje jekla in
nekovinskih materialov
Safety of machinery - Safety requirements for extrusion presses for steel and non-ferrous
metals
Sicherheit von Maschinen - Sicherheitsanforderungen an Strangpressen für Stahl und
NE-Metalle
Sécurité des machines - Exigences de sécurité pour presses à filer l'acier et les métaux
non ferreux
Ta slovenski standard je istoveten z: EN 14656:2006/FprA1
ICS:
13.110 Varnost strojev Safety of machinery
25.120.10 Kovaški stroji. Stiskalnice. Forging equipment. Presses.
Škarje Shears
SIST EN 14656:2007/kFprA1:2009 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 14656:2007/kFprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 14656:2007/kFprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 14656:2006
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
August 2008
ICS 25.120.10
English Version
Safety of machinery - Safety requirements for extrusion presses
for steel and non-ferrous metals
Sécurité des machines - Exigences de sécurité pour Sicherheit von Maschinen - Sicherheitsanforderungen an
presses à filer l'acier et les métaux non ferreux Strangpressen für Stahl und NE-Metalle
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 322.
This draft amendment A1, if approved, will modify the European Standard EN 14656:2006. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14656:2006/FprA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 14656:2007/kFprA1:2009
EN 14656:2006/FprA1:2009 (E)
Contents Page
Foreword .3
1 Modification to the "Foreword" .4
2 Modification to Clause "2 Normative references" .4
3 Modifications to "5.1.2 Site inspections .7
4 Modification to "5.1.4 Safety layout" .7
5 Modifications to "5.1.6 Railings" .8
6 Modifications to "5.1.9 Warning devices and safety signs" .8
7 Modification to "5.1.11 Electrical equipment" .8
8 Modification to "5.1.13 Guards" .9
9 Modifications to "5.1.14 Surface temperatures" .9
10 Modifications to "5.1.16 Hydraulic and pneumatic systems" and "5.1.17 Ergonomics" .9
11 Addition of "5.1.18 Vibrations", "5.1.19 Loss of energy" and "5.1.20 Linked equipment" . 10
12 Modification to Table 1, "5.2.4.1 Mechanical hazards" . 11
13 Modification to Table 1, "5.2.4.6 Ergonomic hazards" and "5.2.4.7 Noise" . 12
14 Modifi
...