|
SIST EN 1870-13:2008+A1:2009/kFprA2:2011
01-december-2011
9DUQRVWOHVQRREGHORYDOQLKVWURMHY.URåQHåDJHGHO +RUL]RQWDOQHNURåQH
åDJH]DUD]UH]SORãþ'RSROQLOR$
Safety of woodworking machines - Circular sawing machines - Part 13: Horizontal beam
panel sawing machines
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen- Teil 13: Horizontale
Plattenkreissägemaschinen mit Druckbalken
Sécurité des machines pour le travail du bois - Machines à scies circulaires - Partie 13:
Scies à panneaux horizontales à presseur
Ta slovenski standard je istoveten z: EN 1870-13:2007+A1:2009/FprA2
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870- en,fr,de
13:2008+A1:2009/kFprA2:2011
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1870-13:2008+A1:2009/kFprA2:2011
---------------------- Page: 2 ----------------------
SIST EN 1870-13:2008+A1:2009/kFprA2:2011
EUROPEAN STANDARD
FINAL DRAFT
EN 1870-13:2007+A1:2009
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA2
September 2011
ICS 79.120.10
English Version
Safety of woodworking machines - Circular sawing machines -
Part 13: Horizontal beam panel sawing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scies circulaires - Partie 13: Scies à panneaux horizontales Kreissägemaschinen- Teil 13: Horizontale
à presseur Plattenkreissägemaschinen mit Druckbalken
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A2, if approved, will modify the European Standard EN 1870-13:2007+A1:2009. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion
of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-13:2007+A1:2009/FprA2:2011:
worldwide for CEN national Members. E
---------------------- Page: 3 ----------------------
SIST EN 1870-13:2008+A1:2009/kFprA2:2011
EN 1870-13:2007+A1:2009/FprA2:2011 (E)
Contents Page
Foreword .4
1 Modifications throughout the whole document .5
2 Modifications to the Foreword .5
3 Modification to the Introduction .6
4 Modifications to Clause 1, Scope .6
5 Modifications to Clause 2, Normative references .6
6 Modifications to Clause 3, Terms and definitions .7
7 Modifications to Clause 4, List of significant hazards .7
8 Modifications to 5.1, General . 10
9 Modifications to 5.2.1.1, General .
...