EN 1870-14:2007+A1:2009/FprA2

Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines

EN 1870-14:2007+A1:2009/FprA2

Name:EN 1870-14:2007+A1:2009/FprA2   Standard name:Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines
Standard number:EN 1870-14:2007+A1:2009/FprA2   language:English language
Release Date:   technical committee:CEN/TC 142 - Woodworking machines - Safety
Drafting committee:CEN/TC 142/WG 4 - Circular sawing machines   ICS number:79.120.10 - Woodworking machines
SLOVENSKI STANDARD
SIST EN 1870-14:2008+A1:2009/kFprA2:2011
01-december-2011
Varnost lesnoobdelovalnih strojev - Krožne žage - 14. del: Vertikalne krožne žage
Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel
sawing machines
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen- Teil 14:
Vertikalplattenkreissägemaschinen
Sécurité des machines pour le travail du bois - Machines à scies circulaires - Partie 14:
Scies à panneaux verticales
Ta slovenski standard je istoveten z: EN 1870-14:2007+A1:2009/FprA2
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870- en,fr,de
14:2008+A1:2009/kFprA2:2011
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1870-14:2008+A1:2009/kFprA2:2011

---------------------- Page: 2 ----------------------

SIST EN 1870-14:2008+A1:2009/kFprA2:2011


EUROPEAN STANDARD
FINAL DRAFT
EN 1870-14:2007+A1:2009
NORME EUROPÉENNE

EUROPÄISCHE NORM
FprA2
September 2011
ICS 79.120.10
English Version
Safety of woodworking machines - Circular sawing machines -
Part 14: Vertical panel sawing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scies circulaires - Partie 14: Scies à panneaux verticales Kreissägemaschinen- Teil 14:
Vertikalplattenkreissägemaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.

This draft amendment A2, if approved, will modify the European Standard EN 1870-14:2007+A1:2009. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion
of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-14:2007+A1:2009/FprA2:2011:
worldwide for CEN national Members. E

---------------------- Page: 3 ----------------------

SIST EN 1870-14:2008+A1:2009/kFprA2:2011
EN 1870-14:2007+A1:2009/FprA2:2011 (E)
Contents Page
Foreword .4
1 Modifications throughout the whole document .5
2 Modifications to the Foreword .5
3 Modification to the Introduction .6
4 Modification to Clause 1, Scope .6
5 Modifications to Clause 2, Normative references .6
6 Modifications to Clause 3, Terms and definitions .6
7 Modifications to Clause 4, List of significant hazards .7
8 Modifications to 5.1, General .9
9 Modifications to 5.2.1.1, General . 10
10 Modification to 5.2.1.2, Use of well tried components .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27