|
SIST EN 13457:2005/kFprA1:2009
01-november-2009
Stroji za izdelavo obutve ter izdelkov iz usnja in njegovih imitacij - Stroji za
cepljenje, brušenje, rezanje ter nanos in sušenje lepila - Varnostne zahteve
Footwear, leather and imitation leather goods manufacturing machines - Splitting,
skiving, cutting, cementing and cement drying machines - Safety requirements
Maschinen zur Herstellung von Schuhen, Leder- und Kunstlederewaren - Spalt-, Schärf-,
Schneid-, Klebstoffauftrag- und Klebstofftrockenmaschinen - Sicherheitsanforderungen
Machines de fabrication de chaussures et d'articles en cuir et en matériaux similaires -
Machines à refendre, à parer, à couper, à encoller et à sécher l'adhésif - Prescriptions de
sécurité
Ta slovenski standard je istoveten z: EN 13457:2004/FprA1
ICS:
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
61.060 Obuvala Footwear
SIST EN 13457:2005/kFprA1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13457:2005/kFprA1:2009
---------------------- Page: 2 ----------------------
SIST EN 13457:2005/kFprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 13457:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
September 2009
ICS 59.140.40; 61.060
English Version
Footwear, leather and imitation leather goods manufacturing
machines - Splitting, skiving, cutting, cementing and cement
drying machines - Safety requirements
Machines de fabrication de chaussures et d'articles en cuir Maschinen zur Herstellung von Schuhen, Leder- und
et en matériaux similaires - Machines à refendre, à parer, à Kunstlederewaren - Spalt-, Schärf-, Schneid-,
couper, à encoller et à sécher l'adhésif - Prescriptions de Klebstoffauftrag- und Klebstofftrockenmaschinen -
sécurité Sicherheitsanforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 201.
This draft amendment A1, if approved, will modify the European Standard EN 13457:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13457:2004/FprA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
Foreword
This document (EN 13457:2004/FprA1:2009) has been prepared by WG 8 of Technical Committee
CEN/TC 201 “Leather and imitation leather goods and footwear manufacturing machinery - Safety”, the
secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
The first reason for amending the published standard EN 13457:2004 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards cited in the
Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
2
---------------------- Page: 4 ----------------------
SIST EN 13457:2005/kFprA1:2009
EN 13457:2004/FprA1:2009 (E)
1 Modification to the Foreword
th
Delete the existing 4 paragraph and replace it with the following: "For relationship with EU Directive(s), see
informative Annexes ZA and ZB, which are integral parts of this document."
2 Modification to the Introduction
st
Delete the 1 paragraph.
nd
In the 2 paragraph, replace "EN 1070" with "EN ISO 12100".
th
Delete the 5 paragraph.
3 Modification to Clause 1, Scope
1.3:
After “ .intended use” add “ , f
...