|
SIST EN 972:2000/kprA1:2010
01-september-2010
6WURMDUVNLVWURML9DOMþQLVWURML9DUQRVWQH]DKWHYH
Tannery machines - Reciprocating roller machines - Safety requirements
Gerberei-Maschinen - Walzenmaschinen - Sicherheitsanforderungen
Machines de tannerie - Machines à cylindres alternatifs - Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 972:1998/FprA1
ICS:
59.140.40 Stroji in oprema za Machines and equipment for
proizvodnjo usnja in krzna leather and fur production
SIST EN 972:2000/kprA1:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 972:2000/kprA1:2010
---------------------- Page: 2 ----------------------
SIST EN 972:2000/kprA1:2010
EUROPEAN STANDARD
FINAL DRAFT
EN 972:1998
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
May 2010
ICS 59.140.40
English Version
Tannery machines - Reciprocating roller machines - Safety
requirements
Machines de tannerie - Machines à cylindres alternatifs - Gerberei-Maschinen - Walzenmaschinen -
Prescriptions de sécurité Sicherheitsanforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 200.
This draft amendment A1, if approved, will modify the European Standard EN 972:1998. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 972:1998/FprA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 972:2000/kprA1:2010
EN 972:1998/FprA1:2010 (E)
Foreword
This document (EN 972:1998/FprA1:2010) has been prepared by Technical Committee CEN/TC 200 “Tannery
machinery - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
The first reason for amending the published standard EN 972:1998 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards cited in the
Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
2
---------------------- Page: 4 ----------------------
SIST EN 972:2000/kprA1:2010
EN 972:1998/FprA1:2010 (E)
1 Modification to the Introduction
Replace the complete text with the following:
"This document is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.".
2 Modifications to Clause 1, Scope
st
Replace the following text in the 1 paragraph “3.11 a) of EN 292-1:1991” with “5.3 a) of
EN ISO 12100-1:2003”.
th
Replace the 5 paragraph “This European Standard applies to the machine manufactured after its date of
issue.” with the following: "This European Standard is not applicable to reciprocating roller machines which
are manufactured before the date of its publication as EN.".
th
Add the following paragraph after the 5 paragraph “This European Standard provides provisions for the
reduction of noise emission at the design stage (see 5.2.4 and Annex A). Howev
...