EN 13675:2004/FprA1

Safety of machinery - Safety requirements for tube forming and rolling mills and finishing line equipment

EN 13675:2004/FprA1

Name:EN 13675:2004/FprA1   Standard name:Safety of machinery - Safety requirements for tube forming and rolling mills and finishing line equipment
Standard number:EN 13675:2004/FprA1   language:English language
Release Date:   technical committee:CEN/TC 322 - Equipments for making and shaping of metals - Safety requirements
Drafting committee:CEN/TC 322/WG 3 - Rolling mills and finishing line equipment   ICS number:77.080 - Ferrous metals
SLOVENSKI STANDARD
SIST EN 13675:2004/kFprA1:2009
01-oktober-2009
Varnost strojev - Varnostne zahteve za cevarne, valjarne in opremo za pakiranje
blaga
Safety of machinery - Safety requirements for tube forming and rolling mills and finishing
line equipment
Sicherheit von Maschinen - Sicherheitsanforderungen an Rohrform- und Rohrwalzwerke
und Adjustageanlagen
Sécurité des machines - Prescriptions pour formeuses et laminoirs à tubes et de lignes
de parachèvement
Ta slovenski standard je istoveten z: EN 13675:2004/FprA1
ICS:
13.110 Varnost strojev Safety of machinery
77.180 Oprema za metalurško Equipment for the
industrijo metallurgical industry
SIST EN 13675:2004/kFprA1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13675:2004/kFprA1:2009

---------------------- Page: 2 ----------------------

SIST EN 13675:2004/kFprA1:2009


EUROPEAN STANDARD
FINAL DRAFT
EN 13675:2004
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
August 2009
ICS 77.180
English Version
Safety of machinery - Safety requirements for tube forming and
rolling mills and finishing line equipment
Sécurité des machines - Prescriptions pour formeuses et Sicherheit von Maschinen - Sicherheitsanforderungen an
laminoirs à tubes et de lignes de parachèvement Rohrform- und Rohrwalzwerke und Adjustageanlagen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 322.

This draft amendment A1, if approved, will modify the European Standard EN 13675:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.



Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13675:2004/FprA1:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13675:2004/kFprA1:2009
EN 13675:2004/FprA1:2009 (E)
Contents Page
Foreword .3
1 Modification to the "Foreword" .4
2 Modification to the Clause "1 Scope" .4
3 Modification to the "Introduction" .4
4 Modification to Clause "2 Normative references" .4
5 Modification to Clause "3 Terms and definitions" .7
6 Modification to Clause "4 List of significant hazards" .7
7 Modification to Clause "5 Safety Requirements and/or measures" and 5.1 .7
8 Modification to "5.2 List of hazards, hazardous situations, safety requirements and/or
measures (Table 1)" . 13
9 Modification to Table 1 . 14
10 Modification to "5.3.4 Hydraulic and pneumatic system" . 15
11 Modification to 5.4.1 " Noise reduction at source by design" . 15
12 Modification to "7.1 Ge
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27