EN 14067-4:2013/prA1:2017

Railway applications - Aerodynamics - Part 4: Requirements and test procedures for aerodynamics on open track

EN 14067-4:2013/prA1:2017

Name:EN 14067-4:2013/prA1:2017   Standard name:Railway applications - Aerodynamics - Part 4: Requirements and test procedures for aerodynamics on open track
Standard number:EN 14067-4:2013/prA1:2017   language:English language
Release Date:   technical committee:CEN/TC 256 - Railway applications
Drafting committee:CEN/TC 256/WG 6 - Aerodynamics   ICS number:45.060.01 - Railway rolling stock in general

SLOVENSKI STANDARD
01-januar-2018
Železniške naprave - Aerodinamika - 4. del: Zahteve in preskusni postopki za
aerodinamiko na odprti progi
Railway applications - Aerodynamics - Part 4: Requirements and test procedures for
aerodynamics on open track
Bahnanwendungen - Aerodynamik - Teil 4: Anforderungen und Prüfverfahren für
Aerodynamik auf offener Strecke
Applications ferroviaires - Aérodynamique - Partie 4: Exigences et procédures d'essai
pour l'aérodynamique à l'air libre
Ta slovenski standard je istoveten z: EN 14067-4:2013/prA1:2017
ICS:
45.060.01 Železniška vozila na splošno Railway rolling stock in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
EN 14067-4:2013
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
October 2017
ICS 45.060.01
English Version
Railway applications - Aerodynamics - Part 4:
Requirements and test procedures for aerodynamics on
open track
Applications ferroviaires - Aérodynamique - Partie 4: Bahnanwendungen - Aerodynamik - Teil 4:
Exigences et procédures d'essai pour l'aérodynamique Anforderungen und Prüfverfahren für Aerodynamik
à l'air libre auf offener Strecke
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 256.

This draft amendment A1, if approved, will modify the European Standard EN 14067-4:2013. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14067-4:2013/prA1:2017:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Addition of Annex ZA, "Relationship between this European Standard and the
essential requirements of EU Directive 2008/57/EC aimed to be covered" . 4

European foreword
This document (EN 14067-4:2013/prA1:2017) has been prepared by Technical Committee CEN/TC 256
“Railway applications”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2008/57/EC.
For relationship with EU Directive 2008/57/EC, see informative Annex ZA, which is an integral part of
this document.
1 Modification to the European foreword
Add the following two paragraphs:
"This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requi
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27