|
SIST EN 12418:2000/kprA1:2008
01-december-2008
5H]DOQLNLNDPHQMDQDJUDGELãþLK9DUQRVW
Masonry and stone cutting-off machines for job site - Safety
Steintrennmaschinen für den Baustelleneinsatz - Sicherheit
Scies de chantier à tronçonner les matériaux - Sécurité
Ta slovenski standard je istoveten z: EN 12418:2000/prA1
ICS:
91.220 Gradbena oprema Construction equipment
SIST EN 12418:2000/kprA1:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12418:2000/kprA1:2008
---------------------- Page: 2 ----------------------
SIST EN 12418:2000/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 12418:2000
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2008
ICS 91.220
English Version
Masonry and stone cutting-off machines for job site - Safety
Scies de chantier à tronçonner les matériaux - Sécurité Steintrennmaschinen für den Baustelleneinsatz - Sicherheit
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 12418:2000. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12418:2000/prA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12418:2000/kprA1:2008
EN 12418:2000/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to the Introduction.4
3 Modification to Clause 2, Normative references .4
4 Modification to Clause 3, Terms and definitions.5
5 Modification to Clause 5, Safety requirements and/or measures.5
6 Modification to 5.1.2.1, Transmission parts.6
nd
7 Modification to 5.1.9.1, General; 5.2.1, General (2 paragraph).6
8 Modification to 5.1.5, Transport and handling.6
9 Modification to 5.2.1, General.6
10 Modification to 5.2.2, Water damp.6
11 Modification to 5.3, Thermal hazards .6
12 Modification to Clause 7, Information for use .7
13 Modification to Annex A (informative) Noise test code – Grade 2 of accuracy .8
14 Modification to C.2.1, Calculation method .10
15 Addition of Annex F.10
16 Modification of Annex ZA .
...