|
SIST EN 13120:2009/oprA1:2012
01-junij-2012
1RWUDQMDVHQþLOD=DKWHYDQHODVWQRVWLYNOMXþQR]YDUQRVWMR
Internal blinds - Performance requirements including safety
Abschlüsse innen - Leistungs- und Sicherheitsanforderungen
Stores intérieurs - Exigences de performance, y compris la sécurité
Ta slovenski standard je istoveten z: EN 13120:2009/prA1
ICS:
91.060.50 Vrata in okna Doors and windows
SIST EN 13120:2009/oprA1:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13120:2009/oprA1:2012
---------------------- Page: 2 ----------------------
SIST EN 13120:2009/oprA1:2012
EUROPEAN STANDARD
DRAFT
EN 13120:2009
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
April 2012
ICS 91.060.50
English Version
Internal blinds - Performance requirements including safety
Stores intérieurs - Exigences de performance, y compris la Abschlüsse innen - Leistungs- und
sécurité Sicherheitsanforderungen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 33.
This draft amendment A1, if approved, will modify the European Standard EN 13120:2009. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13120:2009/prA1:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13120:2009/oprA1:2012
EN 13120:2009/prA1:2012 (E)
Contents Page
Foreword .3
1 Modification to 1, Scope .4
2 Modifications to 2, Normative references .4
3 Modifications to 3, Terms and definitions .5
4 Modifications to 7, Mechanical endurance (repeated operation cycles) .5
5 Modifications to 8, Safety in use .5
6 Modifications to 15, Information for installation, use and maintenance . 10
7 Modifications to Annex C, Common safety devices and measures . 12
8 Addition of a new Annex D, Small part cylinder . 16
9 Modification to the bibliography . 17
2
---------------------- Page: 4 ----------------------
SIST EN 13120:2009/oprA1:2012
EN 13120:2009/prA1:2012 (E)
Foreword
This document (EN 13120:2009/prA1:2012) has been prepared by Technical Committee CEN/TC 33 “Doors,
windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
3
---------------------- Page: 5 ----------------------
SIST EN 13120:2009/oprA1:2012
EN 13120:2009/prA1:2012 (E)
1 Modifications to 1, Scope
nd
In the 2 paragraph, replace “the internal blinds” by “all
...