|
SIST EN 1013:2013/kFprA1:2014
01-april-2014
3URVRMQHHQRVORMQHSURILOLUDQHSROLPHUQHSORãþH]DQRWUDQMHLQ]XQDQMHVWUHKH
VWHQHLQVWURSH=DKWHYHLQSUHVNXVQHPHWRGH
Light transmitting single skin profield plastics sheets for internal and external roofs, walls
and ceilings - Requirements and test methods.
Lichtdurchlässige, einschalige profilierte Platten aus Kunststoff für Innen- und
Außenanwendungen an Dächern, Wänden und Decken - Anforderungen und
Prüfverfahren
Plaques d'éclairement profilées, simple paroi, en matière plastique, pour toitures,
bardages et plafonds intérieurs et extérieurs - Exigences et méthodes d'essai
Ta slovenski standard je istoveten z: EN 1013:2012/FprA1
ICS:
83.140.10 Filmi in folije Films and sheets
91.060.10 Stene. Predelne stene. Walls. Partitions. Facades
Fasade
91.060.20 Strehe Roofs
91.060.30 Stropi. Tla. Stopnice Ceilings. Floors. Stairs
SIST EN 1013:2013/kFprA1:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1013:2013/kFprA1:2014
---------------------- Page: 2 ----------------------
SIST EN 1013:2013/kFprA1:2014
EUROPEAN STANDARD
FINAL DRAFT
EN 1013:2012
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
February 2014
ICS 83.140.10; 91.060.01
English Version
Light transmitting single skin profield plastics sheets for internal
and external roofs, walls and ceilings - Requirements and test
methods.
Plaques d'éclairement profilées, simple paroi, en matière Lichtdurchlässige, einschalige profilierte Platten aus
plastique, pour toitures, bardages et plafonds intérieurs et Kunststoff für Innen- und Außenanwendungen an Dächern,
extérieurs - Exigences et méthodes d'essai Wänden und Decken - Anforderungen und Prüfverfahren
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 128.
This draft amendment A1, if approved, will modify the European Standard EN 1013:2012. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1013:2012/FprA1:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1013:2013/kFprA1:2014
EN 1013:2012/FprA1:2014 (E)
Contents Page
Foreword .3
1 Modification to Clause 2 .4
2 Modification to subclause 5.20 .4
3 Modification to Clause 7 .4
4 Modification to Annex ZA .9
5 Modification to the Bibliography . 21
2
---------------------- Page: 4 ----------------------
SIST EN 1013:2013/kFprA1:2014
EN 1013:2012/FprA1:2014 (E)
Foreword
This document (EN 1013:2012/FprA1:2014) has been prepared by Technical Comm
...