|
SLOVENSKI STANDARD
01-marec-2023
Nadomešča:
SIST EN 843-5:2007
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Weibullova
statistika za podatke o trdnosti (ISO 20501:2019)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Weibull statistics for
strength data (ISO 20501:2019)
Hochleistungskeramik - Weibullstatistik von Festigkeitswerten (ISO 20501:2019)
Céramiques techniques - Analyse statistique de Weibull des données de résistance à la
rupture (ISO 20501:2019)
Ta slovenski standard je istoveten z: EN ISO 20501:2022
ICS:
81.060.30 Sodobna keramika Advanced ceramics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 20501
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2022
EUROPÄISCHE NORM
ICS 81.060.30 Supersedes EN 843-5:2006
English Version
Fine ceramics (advanced ceramics, advanced technical
ceramics) - Weibull statistics for strength data (ISO
20501:2019)
Céramiques techniques - Analyse statistique de Hochleistungskeramik - Weibullstatistik von
Weibull des données de résistance à la rupture (ISO Festigkeitswerten (ISO 20501:2019)
20501:2019)
This European Standard was approved by CEN on 20 December 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20501:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
The text of ISO 20501:2019 has been prepared by Technical Committee ISO/TC 206 "Fine ceramics” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 20501:2022
by Technical Committee CEN/TC 184 “Advanced technical ceramics” the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2023, and conflicting national standards shall be
withdrawn at the latest by June 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 843-5:2006.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 20501:2019 has been approved by CEN as EN ISO 20501:2022 without any modification.
INTERNATIONAL ISO
STANDARD 20501
Second edition
2019-03
Fine ceramics (advanced ceramics,
advanced technical ceramics) —
Weibull statistics for strength data
Céramiques techniques — Analyse statistique de Weibull des données
de résistance à la rupture
Reference number
ISO 20501:2019(E)
©
ISO 2019
ISO 20501:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO 20501:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Defect populations . 1
3.2 Mechanical testing . 3
3.3 Statistical terms . 3
3.4 Weibull distributions . 4
4 Symbols . 5
5 Significance and use . 6
6 Method A: maximum likelihood parameter estimators for single flaw populations .7
6.1 General . 7
6.2 Censored data . 8
6.3 Likelihood functions . 8
6.4 Bias correction . 8
6.5 Confidence intervals .10
7 Method B: maximum likelihood parameter estimators for competing flaw populations .13
7.1 General .13
7.2 Censored data .14
7.3 Likelihood functions .14
8 Procedure.15
8.1 Outlying observations .15
8.2 Fractography .15
8.3 Graphical representation .16
9 Test report .18
Annex A (informative) Converting to material-specific strength distribution parameters .19
Annex B (informative) Illustrative examples .21
Annex C (informative) Test specimens with unidentified fracture origin .28
Annex D (informative) Fortran program .31
Bibliography .36
ISO 20501:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 206, Fine ceramics.
This second edition cancels and replaces the first edition (ISO 20501:2003), which has been technically
revised. It also incorporates the Technical Corrigendum ISO 20501:2003/Cor.1:2009.
The main changes compared to the previous edition are as follows:
— the terms and definitions in Clause 3 have been updated and modified;
— a method to treat a higher number of specimens (N > 120) has been introduced for method A:
maximum likelihood parameter estimators for single fla
...